| Electronic Components Datasheet Search |
|
NT5CB128M16IP-EKB Datasheet(PDF) 147 Page - Nanya Technology Corporation. |
|
|
|||||||||||||||||||||||||||||
NT5CB128M16IP-EKB Datasheet(HTML) 147 Page - Nanya Technology Corporation. |
|
147 / 162 page ![]() Version 2.1 147 Nanya Technology Cooperation © 07/2017 All Rights Reserved. NTC Proprietary Level: Property DDR3(L) 2Gb SDRAM NT5CB(C)256M8IN / NT5CB(C)128M16IP RTT_Nom and RTT_WR turn-off time from ODTLoff reference tAOF 0.3 0.7 0.3 0.7 0.3 0.7 tCK(avg) RTT dynamic change skew tADC 0.3 0.7 0.3 0.7 0.3 0.7 tCK(avg) Write Leveling Timings First DQS/ rising edge after write leveling mode is programmed tWLMRD 40 - 40 - 40 - nCK DQS/ delay after write leveling mode is programmed tWLDQSEN 25 - 25 - 25 - nCK Write leveling setup time from rising CK, crossing to rising DQS, crossing tWLS 165 - 140 - 125 - ps Write leveling hold time from rising DQS, crossing to rising CK, crossing tWLH 165 - 140 - 125 - ps Write leveling output delay tWLO 0 7.5 0 7.5 0 7.5 ns Write leveling output error tWLOE 0 2 0 2 0 2 ns Jitter Notes Note 1 Unit “tCK(avg)” represents the actual tCK(avg) of the input clock under operation. Unit “nCK” represents one clock cycle of the input clock, counting the actual clock edges. ex) tMRD=4 [nCK] means; if one Mode Register Set command is registered at Tm, another Mode Register Set command may be registered at Tm+4, even if (Tm+4-Tm) is 4 x tCK(avg) + tERR (4per), min. Note 2 These parameters are measured from a command/address signal (CKE, , RA, A, WE, ODT, BA0, A0, A1, etc) transition edge to its respective clock signal (CK/ ) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT(per), tJIT(cc), etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these parameters should be met whether clock jitter is present or not. Note 3 These parameters are measured from a data strobe signal (DQS(L/U), LU)) crossing to its respective clock signal (CK, ) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT(per), tJIT(cc), etc), as these are relative to the clock signal crossing. That is, these parameters should be met whether clock jitter is present or not. Note 4 These parameters are measured from a data signal (DM(L/U), DQ(L/U)0, DQ(L/U)1, etc.) transition edge to its respective data strobe signal (DQS(L/U), LU) crossing. Note 5 For these parameters, the DDR3(L) SDRAM device supports tnPARAM [nCK] = RU{Tparam[ns] / tCK(avg)[ns]}, which is in clock cycles, assuming all input clock jitter specifications are satisfied. Note 6 When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR (mper), act of the input clock, where 2 <= m <=12. (Output derating is relative to the SDRAM input clock.) Note 7 When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT(per),act of the input clock. (Output deratings are relative to the SDRAM input clock.) |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |