ATmega325P datasheet(305/364 Pages) ATMEL

305 / 364 page

305

8023F–AVR–07/09

ATmega325P/3250P

Notes:

1. “Max” means the highest value where the pin is guaranteed to be read as low

2. “Min” means the lowest value where the pin is guaranteed to be read as high

3. Although each I/O port can sink more than the test conditions (20 mA at V

CC = 5V, 10 mA at VCC = 3V for Port B and 10 mA

at V

CC = 5V, 5 mA at VCC = 3V for all other ports) under steady state conditions (non-transient), the following must be

observed:

TQFP and QFN/MLF Package:

1] The sum of all IOL, for all ports, should not exceed 400 mA.

2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.

3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.

4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.

5] The sum of all IOL, for ports F0 - F7, should not exceed 100 mA.

If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater

than the listed test condition.

4. Although each I/O port can source more than the test conditions (20 mA at VCC = 5V, 10 mA at VCC = 3V for Port B and 10mA

at V

CC = 5V, 5 mA at VCC = 3V for all other ports) under steady state conditions (non-transient), the following must be

observed:

TQFP and QFN/MLF Package:

1] The sum of all IOL, for all ports, should not exceed 400 mA.

2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.

3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.

4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.

5] The sum of all IOL, for ports F0 - F7, should not exceed 100 mA.

If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current

greater than the listed test condition.

5. Typical values at 25

⋅C.

ICC

Power Supply Current

Active 1 MHz, VCC = 2V

0.5

0.75

Active 4 MHz, VCC = 3V

2.6

3.5

Active 8 MHz, VCC = 5V

Idle 1 MHz, VCC = 2V

0.14

0.25

Idle 4 MHz, VCC = 3V

0.75

1.5

Idle 8 MHz, VCC = 5V

2.9

Power-save mode

32 kHz TOSC enabled,

VCC = 1.8V

0.75

µA

32 kHz TOSC enabled,

VCC = 3V

1µA

Power-down mode(5)

WDT enabled, VCC = 3V

6.7

µA

WDT disabled, VCC = 3V

0.2

µA

VACIO

Analog Comparator

Input Offset Voltage

VCC = 5V

Vin = VCC/2

<10

IACLK

Analog Comparator

Input Leakage Current

VCC = 5V

Vin = VCC/2

-50

tACID

Analog Comparator

Propagation Delay

VCC = 2.7V

VCC = 4.0V

750

500

A = -40⋅C to 85⋅C, VCC = 1.8V to 5.5V (unless otherwise noted) (Continued)

Symbol

Parameter

Condition

Min.

Typ.

Max.

Units

ATmega325P Datasheet(PDF) 305 Page - ATMEL Corporation

ATmega325P Datasheet(HTML) 305 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL