04 | Keysight | Infiniium DCA-X 86100D Wide-Bandwidth Oscilloscope Mainframe and Modules - Data Sheet

General and mainframe

Specifications describe warranted performance over the

temperature range of +10 to +40 °C (unless otherwise noted).

The specifications are applicable for the temperature after the

instrument is turned on for one hour, and while self-calibration

is valid. Many performance parameters are enhanced through

frequent, simple user calibrations. Characteristics provide useful,

non-warranted information about the functions and performance

of the instrument. Characteristics are printed in italic typeface.

Product specifications and descriptions in this document are

subject to change without notice.

General specifications

Temperature

Operating

10 to +40 °C (50 to +104 °F)

Non-operating

–40 to +65 °C (–40 to +158 °F)

Altitude

Operating

Up to 4,600 meters (15,000 feet)

Power (max)

100/120 Vac 50/60/400 Hz

With typical modules: 150 to 230 VA at 25 °C

220/240 Vac 50/60 Hz, 700 W maximum

Weight

Mainframe without modules

20.5 kg (43 lbs)

Typical module

1.2 kg (2.6 lbs)

Mainframe dimensions (excluding handle) Without front connectors and rear feet

221 mm (H) x 426 mm (W) x 530 mm (D)

(7 in x 16.76 in x 20.9 in)

With front connectors and rear feet

234 mm (H) x 426 mm (W) x 601 mm (D)

(9.23 in x 16.76 in x 23.67 in)

With front cover and rear feet

234 mm (H) x 426 mm (W) x 612 mm (D)

(9.23 in x 16.76 in x 24.1 in)

Max relative humidity

80% for temperatures up to 31 °C decreasing linearly to 50% relative humidity at 40 °C

Supply voltage variation

86100D system can operate with supply voltage fluctuations up to ± 10% of the nominal voltage

Mainframe specifications

Horizontal system (time base)

Pattern lock

Scale factor (full scale is ten divisions)

Minimum

2 ps/div (with 86107A or 86100D-PTB: 500 fs/div)

Maximum

1 s/div

250 ns/div

Minimum

24 ns

40.1 ns default, 24 ns min

Maximum

1000 screen diameters or 10 s whichever is smaller

1000 screen diameters or 25.401 μs whichever is smaller

1 ps + 1.0% of Δ time reading or 8 ps, whichever is smaller

Time interval accuracy - jitter mode operation 1 ps

Time interval resolution

≤ (screen diameter)/(record length) or 62.5 fs, whichever is

larger

Display units

Bits or time (TDR mode–meters)

Vertical system (channels)

Number of channels

16 (simultaneous acquisition)

Vertical resolution

54xxx, 83xxx, 86xxx: 14 bit A/D converter (16 or more bits with averaging). N10xx: 16 bit A/D converter

Full resolution channel

Adjusts in a 1-2-5-10 sequence for coarse adjustment or fine adjustment resolution from the front panel knob

Adjustments

Scale, offset, activate filter, sampler bandwidth, attenuation factor, transducer conversion factors

Record length

Legacy UI: 16 to 16 K samples

FlexDCA without pattern lock: 16 to 64 K samples

1. Time offset relative to the front panel trigger input on the instrument mainframe.

2. Dual marker measurement performed at a temperature within 5 °C of horizontal calibration temperature.

3. The maximum delay setting is 100 ns and delta time does not span across (28 + Nx4) ns ± 100 ps delay setting, where N=0,1,2….18. If delta time

measurement span exceeds above criteria, time interval accuracy is 8 ps +0.1% of Δ time reading.

4. Characteristic performance. Test configuration: PRBS of length 127 bits, Data and Clock 10 Gb/s.

5. Maximum number of samples depends on pattern, number of active channels and available memory.

Specifications

Comparing specifications

When comparing performance attributes between instruments,

ensure you compare the same type of parameter. For example,

compare warranted specifications from both instruments, or

compare characteristics or typical performance. Warranted

specifications include measurement uncertainties and are

conservative compared to other types of unwarranted attributes.

Factory calibration cycle - For optimum performance, the

instrument should have a complete verification of specifications

once every twelve months.