DLPC3470 datasheet(41/70 Pages) TI1

41 / 70 page

DLPC3470

www.ti.com

DLPS110 – APRIL 2018

Product Folder Links: DLPC3470

Submit Documentation Feedback

(1)

Only the first data byte is show, data continues

(2)

DLPC3470 controller does not support access to a second/ expansion Write Status byte

Table 5. SPI Flash Instruction OpCode and Access Profile Compatibility Requirements

SPI FLASH COMMAND

FIRST BYTE

(OPCODE)

SECOND

BYTE

THIRD BYTE

FOURTH BYTE

FIFTH BYTE

SIXTH BYTE

Fast READ (1 Output)

0x0B

ADDRS(0)

ADDRS(1)

ADDRS(2)

dummy

DATA(0)(1)

Read status

0x05

n/a

STATUS(0)

Write status

0x01

STATUS(0)

(2)

Write enable

0x06

Page program

0x02

ADDRS(0)

ADDRS(1)

ADDRS(2)

DATA(0)(1)

Sector erase (4KB)

0x20

ADDRS(0)

ADDRS(1)

ADDRS(2)

device erase

0xC7

(1)

The timing values are related to the specification of the flash device itself, not the DLPC3470 controller .

(2)

The DLPC3470 controller does not drive the HOLD or WP (active low write protect) pins on the flash device, and thus these pins should

be tied to a logic high on the PCB through an external pullup.

The specific and timing compatibility requirements for a DLPC3470 controller compatible flash are listed in

Table 6 and Table 7.

Table 6. SPI Flash Key Timing Parameter Compatibility Requirements(1)(2)

SPI FLASH TIMING PARAMETER

SYMBOL

ALTERNATE SYMBOL

MIN

MAX

UNIT

Access frequency

(all commands)

≤1.42

MHz

device select high time (also called device select

deselect time)

tSHSL

tCSH

≤200

Output hold time

tCLQX

tHO

≥0

Clock low to output valid time

tCLQV

≤ 11

Data in set-up time

tDVCH

tDSU

≤5

Data in hold time

tCHDX

tDH

≤5

(1)

The flash supply voltage must match VCC_FLSH on the DLPC3470 controller . Special attention needs to be paid when ordering

devices to be sure the desired supply voltage is attained as multiple voltage options are often available under the same base part

number.

(2)

Beware when considering Numonyx (Micron) serial flash devices as they typically do not have the 4KB sector size needed to be

DLPC3470 controller compatible.

(3)

All of these flash devices appear compatible with the DLPC3470 controller , but only those marked with yes in the DVT column have

been validated on the EVM reference design. Those marked with no can be used at the ODM’s own risk.

The DLPC3470 controller supports 1.8-, 2.5-, or 3.3-V serial flash devices. To do so, VCC_FLSH must be

supplied with the corresponding voltage. Table 7 contains a list of 1.8-, 2.5-, and 3.3-V compatible SPI serial

flash devices supported by DLPC3470 controller .

Table 7. DLPC3470 controller Compatible SPI Flash Device Options(1) (2)

DVT(3)

DENSITY (Mb)

VENDOR

PART NUMBER

PACKAGE SIZE

1.8-V COMPATIBLE DEVICES

Yes

4 Mb

Winbond

W25Q40BWUXIG

2 × 3 mm USON

Yes

4 Mb

Macronix

MX25U4033EBAI-12G

1.43 × 1.94 mm WLCSP

Yes

8 Mb

Macronix

MX25U8033EBAI-12G

1.68 × 1.99 mm WLCSP

2.5- OR 3.3-V COMPATIBLE DEVICES

Yes

16 Mb

Winbond

W25Q16CLZPIG

5 × 6 mm WSON

Yes

32 Mb

Winbond

W25Q32FVSSIG

5.2 x 7.9 mm SOIC

DLPC3470 Datasheet(PDF) 41 Page - Texas Instruments

DLPC3470 Datasheet(HTML) 41 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

Datasheet Download

Link URL