DR10E03XR datasheet(2/7 Pages) CRYDOM

2 / 7 page

Datasheet

DIN Rail Mount

INPUT SPECIFICATIONS (2)

DRxxExx

DRxxBxx

DRxxDxx

Description

Control Voltage Range (6)

4-32 VDC

200-265 Vrms

18-36 Vrms (1)

Minimum Turn-On Voltage

4.0 VDC

200 Vrms

18 Vrms

Must Turn-Off Voltage

1.0 VDC

40 Vrms

4 Vrms

Minimum Input Current for [mA] (7)

2.5

3.5

Maximum Input Current for [mA] (8)

3.3

1/2 Cycle

20 msec

Maximum Turn-on Time [msec] (8) (9)

1/2 Cycle

30 msec

Maximum Turn-off Time [msec] (10)

22/16 AWG

GENERAL SPECIFICATIONS(2)

Description

Parameters

Dielectric Strength, Input/Output/Base (50/60Hz)

4000 Vrms (11)

Minimum Insulation Resistance (@ 500 VDC)

Maximum Capacitance, Input/Output

10 pF

Ambient Operating Temperature Range

-30 to 80 °C

Ambient Storage Temperature Range

-30 to 100 °C

4.4-7.0 in-lb (0.5-0.8Nm)

Recommended Terminal Screw Torque Range

109 Ohm

Min/Max stranded/solid wire

DRxxAxx

90-140 Vrms

90 Vrms

10 Vrms

20 msec

30 msec

22/16 AWG

GENERAL NOTES

(2) All parameters at 25°C unless otherwise speciﬁed.

(3) For AC output frequency is 47-63Hz

(5) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1

(6) DC control includes reverse polarity protection.

(7) Input circuitry incorporates active current limiter.

(8) Turn-on time for DC control random turn-on versions is 0.1 msec.

(9) Turn-on time for DC output 600µsec.

(10) Turn-off time for DC output 300

µsec.

(11) 2500 Vrms for DC output.

LC A, Resistive or Slightly Inductive Load Ratings: 3A @40°C ambient for DR24x03, 3A @ 40°C ambient for DR48x03

LC B, Motor Loads Ratings: 0.18KW @ 240VAC for DR24x03 and 0.375KW @ 480VAC DR48x13

Standards of Compliance

IEC 62314

Shock and Vibration (Applies to all part numbers)

Vibration Resistence according to IEC 60068-2-6: 0.35mm and 0.75mm Amplitude over 10-55 Hz

Shock Resistance according to IEC 60068-2-27: 15g/11ms

EMC (Applies to all part numbers)

IEC 61000-4-2: Electrostatic Discharge- Level 3

IEC 61000-4-4: Electrically Fast Transients- Level 3

IEC 61000-4-5: Electrical Surges- Level 3

ANSI / ISA 12.12.01-2013

Nonincendive Electrical Equipment for Use in Class I and II, Division 2 and Class III, Division 1 and 2 Hazadous (classiﬁed) locations

This equipment is open-type device and is meant to be installed in an enclosure suitable for the enviroment such that the equipment is only accesible with the use of a tool

suitable for use in Class 1, Division 2, Group A,B,C and Hazardous locations, or Nonhazardous locations only

WARNING-Explosion Hazard- Do not disconnect equipment while the circuit is live or unless the area is known to be free of ignitable concentrations

WARNING-Explosion Hazard- Substitution of any component may impair suitability for class I, Division 2

(4) See Derating curves

(1) E option is UL certiﬁed for AC control voltage, but it works also with 18-36 VDC input range.

Do not forget to visit us at: www.crydom.com

DR10E03XR Datasheet(PDF) 2 Page - Crydom Inc.,

DR10E03XR Datasheet(HTML) 2 Page - Crydom Inc.,

Html Pages

1 2 3 4 5 6 7

Datasheet Download

Link URL