MODEL: PHS

PHS SPECIFICATIONS

ES-3207 Rev.3 Page 1/4

http://www.m-system.co.jp/

Plug-in Signal Conditioners M-UNIT

PEAK HOLD

(isolated)

Functions & Features

• Track mode: the output follows proportionally to the input

• Peak-hold mode: responds only to an increasing signal,

holding the maximum value until a higher signal or a

command to reset is received

• Minimum value (valley) hold selectable

• LCD meter

• High-density mounting

Typical Applications

• Monitoring peak power consumption

• Monitoring the highest or lowest temperature

50

(1.97)

127

(5)

80

(3.15)

mm (inch)

MODEL: PHS[1]–[2][3]–[4][5]

ORDERING INFORMATION

• Code number: PHS[1]-[2][3]-[4][5]

Specify a code from below for each [1] through [5].

(e.g. PHSH-6A-B/E/Q)

•Special input and output ranges (For codes Z & 0)

• Specify the specification for option code /Q

(e.g. /C01/S01)

[1] HOLD FUNCTION

H: Peak hold

L: Valley hold

[2] INPUT

Current

A: 4 – 20 mA DC (Input resistance 250 Ω)

A1: 4 – 20 mA DC (Input resistance 50 Ω)

B: 2 – 10 mA DC (Input resistance 500 Ω)

C: 1 – 5 mA DC (Input resistance 1000 Ω)

D: 0 – 20 mA DC (Input resistance 50 Ω)

E: 0 – 16 mA DC (Input resistance 62.5 Ω)

F: 0 – 10 mA DC (Input resistance 100 Ω)

G: 0 – 1 mA DC (Input resistance 1000 Ω)

H: 10 – 50 mA DC (Input resistance 100 Ω)

J: 0 – 10 μA DC (Input resistance 1000 Ω)

K: 0 – 100 μA DC (Input resistance 1000 Ω)

GW: -1 – +1 mA DC (Input resistance 1000 Ω)

FW: -10 – +10 mA DC (Input resistance 100 Ω)

Z: Specify current (See INPUT SPECIFICATIONS)

Voltage

1: 0 – 10 mV DC (Input resistance 10 kΩ min.)

15: 0 – 50 mV DC (Input resistance 10 kΩ min.)

16: 0 – 60 mV DC (Input resistance 10 kΩ min.)

2: 0 – 100 mV DC (Input resistance 100 kΩ min.)

3: 0 – 1 V DC (Input resistance 1 MΩ min.)

4: 0 – 10 V DC (Input resistance 1 MΩ min.)

5: 0 – 5 V DC (Input resistance 1 MΩ min.)

6: 1 – 5 V DC (Input resistance 1 MΩ min.)

4W: -10 – +10 V DC (Input resistance 1 MΩ min.)

5W: -5 – +5 V DC (Input resistance 1 MΩ min.)

0: Specify voltage (See INPUT SPECIFICATIONS)

[3] OUTPUT

Current

A: 4 – 20 mA DC (Load resistance 750 Ω max.)

B: 2 – 10 mA DC (Load resistance 1500 Ω max.)

C: 1 – 5 mA DC (Load resistance 3000 Ω max.)

D: 0 – 20 mA DC (Load resistance 750 Ω max.)

E: 0 – 16 mA DC (Load resistance 900 Ω max.)

F: 0 – 10 mA DC (Load resistance 1500 Ω max.)

G: 0 – 1 mA DC (Load resistance 15 kΩ max.)

Z: Specify current (See OUTPUT SPECIFICATIONS)

Voltage

1: 0 – 10 mV DC (Load resistance 10 kΩ min.)

2: 0 – 100 mV DC (Load resistance 100 kΩ min.)

3: 0 – 1 V DC (Load resistance 100 Ω min.)

4: 0 – 10 V DC (Load resistance 1000 Ω min.)

5: 0 – 5 V DC (Load resistance 500 Ω min.)

6: 1 – 5 V DC (Load resistance 500 Ω min.)

4W: -10 – +10 V DC (Load resistance 2000 Ω min.)

5W: -5 – +5 V DC (Load resistance 1000 Ω min.)

0: Specify voltage (See OUTPUT SPECIFICATIONS)