NFAQ1560R43TL

www.onsemi.com

5

Parameter

Symbol

Conditions

Rating

Unit

Supply Voltage

VPN

P−NU,NV,NW, VPN (surge) < 500 V

(Note 2)

450

V

Collector−Emitter Voltage

VCES

P-U,V,W; U-NU; V-NV; W-NW

600

V

Each IGBT Collector Current

IC

P,U,V,W,NU,NV,NW terminal current

±15

A

P,U,V,W,NU,NV,NW terminal current, Tc = 100°C

±7.5

A

Each IGBT Collector Current (Peak)

ICp

Tc = 25°C, Under 1 ms Pulse Width

±30

A

Corrector Dissipation

Pc

Tc = 25°C, Per One Chip (IGBT Part)

50

W

Tc = 25°C, Per One Chip (FRD Part)

26.5

W

High−Side Control Bias voltage

VBS

VB(U)−VS(U), VB(V)−VS(V),

VB(W)−VS(W)

(Note 3)

−0.3 to +20.0

V

Control Supply Voltage

VDD

VDD−VSS

−0.3 to +20.0

V

Input Signal Voltage

VIN

HIN(U), HIN(V), HIN(W), LIN(U), LIN(V), LIN(W) −

VSS

V

FAULT Terminal Voltage

VFAULT

FAULT−VSS

V

CFOD Terminal Voltage

VCFOD

CFOD−VSS

V

SD Terminal Voltage

VSD

SD−VSS

V

Current Sensing Input Voltage

VITRIP

ITRIP−VSS

−0.3 to +10.0

V

Operating Junction Temperature

Tj

150

_C

Storage Temperature

Tstg

−40 to +125

_C

Module Case Operation Temperature

Tc

−40 to +125

_C

Tightening Torque

MT

Case mounting screws

0.6

Nm

Isolation Voltage

Viso

50 Hz sine wave AC 1 minute

(Note 4)

2000

Vrms

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality

should not be assumed, damage may occur and reliability may be affected.

1. Refer to ELECTRICAL CHARACTERISTICS, RECOMMENDED OPERATING RANGES and/or APPLICATION INFORMATION for Safe

Operating parameters

2. This surge voltage developed by the switching operation due to the wiring inductance between P and NU, NV, NW terminal.

3. VBS = VB(U)−VS(U), VB(V)−VS(V), VB(W)−VS(W)

4. Test conditions : AC2500V, 1 s

RECOMMENDED OPERATING RANGES

Rating

Symbol

Conditions

Min

Typ

Max

Unit

Supply Voltage

VPN

P − NU, NV, NW

0

280

450

V

High−Side Control Bias

Voltage

VBS

VB(U) − VS(U), VB(V) − VS(V), VB(W) −

VS(W)

13.0

15

17.5

V

Control Supply Voltage

VDD

VDD − VSS

14.0

15

16.5

V

ON−state Input Voltage

VIN(ON)

HIN(U), HIN(V), HIN(W), LIN(U), LIN(V),

LIN(W) − VSS

3.0

−

5.0

V

OFF−state Input Voltage

VIN(OFF)

0

−

0.3

V

PWM Frequency

fPWM

1

−

20

kHz

Dead Time

DT

Turn−off to Turn−on (external)

2

−

−

ms

Allowable Input Pulse Width

PWIN

ON and OFF

1

−

−

ms

Tightening Torque

‘M3’ Type Screw

0.4

−

0.6

Nm

Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond

the Recommended Operating Ranges limits may affect device reliability.