8

PXAE263708NB

Rev. 04, 2023-06-23

© 2023 Wolfspeed, Inc. All rights reserved. Wolfspeed® and the Wolfstreak logo are registered trademarks and the Wolfspeed logo is a trademark of Wolfspeed, Inc.

The information in this document is subject to change without notice.

4600 Silicon Drive | Durham, NC 27703 | Tel: +1.919.313.5300

Package Outline Specifications

Package PG-HB2SOF-8-1

Diagram Notes–unless otherwise specified:

1. Mold/Dam Bar/Metal protusion of 0.30mm max per side not included.

2. Fillets and radii: all radii are 0.3 mm max unless specified otherwise

3. Interpret dimensions and tolerances per ISO 8015

4. Dimensions are mm

5. Exposed metal surface are tin plated, may not be covered by mold compound

6. Does not include mold/dam bar/metal protusion.

7. All tolerances ± 0.1mm unless specified otherwise

9. All metal surfaces pre-plated, except area of cut

9. Lead thickness: 0.25 mm

10. Pins: D1, D2 – drain; G1, G2 – gate; V – V

DD; GND – ground

32.26

1

2 X 14.12

2.83

7.06

2 X 10.6

2 X 4.44

1.57

3.81

0.25

2 X 1.02

4 X 11.29

2 X 1.00

V

V

2 X 0.8

32.26

6

PG-HB2SOF-8-1_02-05-2018

G2

G1

D2

D1

2 X 0.50

31.26

0.05

G1

G2

D1

D2

Y

V

V

Bottom View

Find the latest and most complete information about products and packaging at the Wolfspeed Internet page www.wolfspeed.com/RF

Diagram Notes–unless otherwise specified:

1. Mold/dam bar/metal protrusion of 0.30 mm max per side not included

2. Fillets and radii: all radii are 0.30 mm max unless specifi ed otherwise

3. Interpret dimensions and tolerances per ISO 8015

4. Dimensions are mm

5. Exposed metal surface are tin plated, may not be covered by mold

compound

6. Does not include mold/dam bar/metal protusion.

7. All tolerances ± 0.1 mm unless specifi ed otherwise

8. All metal surfaces pre-plated, except area of cut

9. Lead thickness: 0.25 mm

10. Pins: D1, D2 – drain; G1, G2 – gate; V – VDD; GND – ground, (Source – bottom

metallization)

Top View

Side View

Diagram Notes–unless otherwise specified:

1. Mold/Dam Bar/Metal protusion of 0.30mm max per side not included.

2. Fillets and radii: all radii are 0.3 mm max unless specified otherwise

3. Interpret dimensions and tolerances per ISO 8015

4. Dimensions are mm

5. Exposed metal surface are tin plated, may not be covered by mold compound

6. Does not include mold/dam bar/metal protusion.

7. All tolerances ± 0.1mm unless specified otherwise

9. All metal surfaces pre-plated, except area of cut

9. Lead thickness: 0.25 mm

10. Pins: D1, D2 – drain; G1, G2 – gate; V – V

DD; GND – ground

32.26

1

2 X 14.12

2.83

7.06

2 X 10.6

2 X 4.44

1.57

3.81

0.25

2 X 1.02

4 X 11.29

2 X 1.00

V

V

2 X 0.8

32.26

6

PG-HB2SOF-8-1_02-05-2018

G2

G1

D2

D1

Y

End View