| Electronic Components Datasheet Search |
|
MP6545 Datasheet(PDF) 3 Page - Monolithic Power Systems |
|
|
|||||||||||||||||||||||||||||
MP6545 Datasheet(HTML) 3 Page - Monolithic Power Systems |
|
3 / 20 page ![]() MP6545 – 45V, 2.5A, SIMPLE THREE-PHASE POWER STAGE MP6545 Rev. 1.1 MonolithicPower.com 3 5/12/2023 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2023 MPS. All Rights Reserved. PIN FUNCTIONS Pin # (QFN) Pin # (TSSOP) Name Description 1, 8 4, 11 VIN Input supply voltage. Decouple the VIN pin to ground using a minimum 100nF ceramic capacitor. Additional bulk capacitance may be required. 2 5 OUT1 Output terminal 1. 3, 6 6, 9 PGND Power ground for half H-bridge outputs. 4 7 OUT2 Output terminal 2. 5 8 OUT3 Output terminal 3. 11, 24 14, 28 GND Signal ground. 12 15 VREG Internal regulator. Connect a 1µF, 16V ceramic capacitor (X7R) to ground. 13 16 nRESET Reset input. Pull the nRESET pin active low to reset the protection circuits and disable the outputs. This pin has an internal pull-down resistor. 14 17 nSLEEP Sleep mode input. Pull the nSLEEP pin logic low to enter low-power sleep mode. This pin has an internal pull-down resistor. 15 18 nFAULT Fault indication. The nFAULT pin is an open-drain output. If used, nFAULT requires an external pull-up resistor. nFAULT is in logic low under fault conditions. 16 20 HS1 High input turns on the OUT1 high-side MOSFET (HS FET). The HS1 pin has an internal pull-down resistor. 17 21 LS1 High input turns on the OUT1 low-side MOSFET (LS FET). The LS1 pin has an internal pull-down resistor. 18 22 HS2 High input turns on the OUT2 HS-FET. The HS2 pin has an internal pull- down resistor. 19 23 LS2 High input turns on the OUT2 LS-FET. The LS2 pin has an internal pull-down resistor. 20 24 HS3 High input turns on the OUT3 HS-FET. The HS3 pin has an internal pull- down resistor. 21 25 LS3 High input turns on the OUT3 LS-FET. The LS3 pin has an internal pull-down resistor. 25 1 CPA Charge pump capacitor. Connect a 100nF ceramic capacitor that is rated for VIN between the CPA and CPB pins. 26 2 CPB 27 3 VCP Charge pump output. The VCP pin requires a 1µF, 16V ceramic capacitor to VIN. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |