ADP130AUJZ-1.2-R7 datasheet(4/20 Pages) AD

4 / 20 page

ADP130

Rev. 0 | Page 4 of 20

Parameter

Symbol

Conditions

Min

Typ

Max

Unit

OUTPUT NOISE

OUTNOISE

10 Hz to 100 kHz, VIN = 3.6 V, VOUT = 0.8 V

μV rms

10 Hz to 100 kHz, VIN = 3.6 V, VOUT = 1.2 V

μV rms

10 Hz to 100 kHz, VIN = 3.6 V, VOUT = 1.5 V

μV rms

10 Hz to 100 kHz, VIN = 3.6 V, VOUT = 2.5 V

μV rms

10 Hz to 100 kHz, VIN = 3.6 V, VOUT = 3.0 V

μV rms

POWER SUPPLY REJECTION RATIO

PSRR

Modulated bias, 10 kHz, VOUT = 3.0 V, VIN = 3.6 V,

VBIAS = 5 V

Modulated bias, 100 kHz, VOUT = 3.0 V, VIN = 3.6 V,

VBIAS = 5 V

Modulated VIN, 10 kHz, VOUT = 1.2 V, VIN = VOUT + 1 V,

VBIAS = 5 V

Modulated VIN, 100 kHz, VOUT = 1.2 V, VIN = VOUT + 1 V,

VBIAS = 5 V

Modulated VIN, 10 kHz, VOUT = 0.8 V, VIN = VOUT + 1 V,

VBIAS = 5 V

Modulated VIN, 100 kHz, VOUT = 0.8 V, VIN = VOUT + 1 V,

VBIAS = 5 V

1 IVIN = IGND − IBIAS, where IGND is the current flowing from the GND pin.

2 Based on an endpoint calculation using 1 mA and 350 mA loads.

3 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output

voltages above 1.3 V.

4 Start-up time is defined as the time from the rising edge of EN to VOUT being at 90% of its nominal value.

5 Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 2.0 V

output voltage is defined as the current that causes the output voltage to drop to 90% of 2.0 V, or 1.8 V.

INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS

Table 2.

Parameter

Symbol

Conditions

Min

Typ

Max

Unit

MINIMUM INPUT AND OUTPUT

CAPACITANCE1

CMIN

TJ = −40°C to +125°C

0.70

μF

CAPACITOR ESR

RESR

TJ = −40°C to +125°C

.001

1 The minimum input and output capacitance should be >0.70 μF over the full range of operating conditions. The full range of operating conditions in the application

must be considered during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended. Y5V and

Z5U capacitors are not recommended for use with any LDO.

ADP130AUJZ-1.2-R7 Datasheet(PDF) 4 Page - Analog Devices

ADP130AUJZ-1.2-R7 Datasheet(HTML) 4 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Datasheet Download

Link URL