| Electronic Components Datasheet Search |
|
LFDW Datasheet(PDF) 16 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LFDW Datasheet(HTML) 16 Page - Linear Technology |
|
16 / 24 page ![]() LT3682 16 3682f APPLICATIONS INFORMATION Figure 2. Model for Loop Response 0.8V LT3682 CF RC VC 3Meg 3682 F02 CURRENT MODE POWER STAGE gm = 1.25S CC CPL C1 R2 R1 SW FB GND OUTPUT CERAMIC POLYMER OR TANTALUM OR ELECTROLITIC ESR + C1 gm = 420μS Table 3. Schottky Diodes PART NUMBER VR (V) IAVE (A) VF at 1A (mV) VF at 2A (mV) On Semiconducor MBR0520L 20 0.5 MBR0540 40 0.5 620 MBRM120E 20 1 530 595 MBRM140 40 1 550 Diodes Inc. B0530W 30 0.5 B0540W 40 0.5 620 B120 20 1 500 B130 30 1 500 B140 40 1 500 B150 50 1 700 B220 20 2 500 B230 30 2 500 B140HB 40 1 DFLS240L 40 2 500 DFLS140 40 1.1 510 B240 40 2 500 Central Semiconductor CMSH1 – 40M 40 1 500 CMSH1 – 60M 60 1 700 CMSH1 – 40ML 40 1 400 CMSH2 – 40M 40 2 550 CMSH2 – 60M 60 2 700 CMSH2 – 40L 40 2 400 CMSH2 – 40 40 2 500 CMSH2 – 60 60 2 700 Frequency Compensation The LT3682 uses current mode control to regulate the output. This simplifies loop compensation. In particular, the LT3682 does not require the ESR of the output capacitor for stability, so you are free to use ceramic capacitors to achieve low output ripple and small circuit size. Frequency Loop compensation determines the stability and transient performance. Optimizing the design of the compensation network depends on the application and type of output capacitor. A practical approach is to start with one of the circuits in this data sheet that is similar to your application and tune the compensation network to optimize the performance. Stability should then be checked across all operating conditions, including load current, input voltage and temperature. The LT1375 data sheet contains a more thorough discussion of loop compensation and describes how to test the stability using a transient load. Figure 2 shows an equivalent circuit for the LT3682 control loop. The error amplifier is a transconductance amplifier with finite output impedance. The power section, consisting of the modulator, power switch and inductor, is modeled as a transconductance amplifier generating an output current proportional to the voltage at the VC pin. Note that the output capacitor integrates this current, and that the compensation is provided by the components tied to the VC pin, as shown in Figure 2. Generally a capacitor (CC) and a resistor (RC) in series to ground are used. In addition, there may be a lower value capacitor in parallel. This capacitor (CF) is used to filter noise at the switching frequency, and is required only if a phase-lead capacitor (CPL) is used or if the output capacitor has high ESR. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |