7

3/10/97

SPT7922

TYPICAL INTERFACE CIRCUIT

The SPT7922 requires few external components to achieve

the stated operation and performance. Figure 2 shows the

typical interface requirements when using the SPT7922 in

normal circuit operation. The following section provides a

description of the pin functions and outlines critical perfor-

mance criteria to consider for achieving the optimal device

performance.

POWER SUPPLIES AND GROUNDING

The SPT7922 requires -5.2 V and +5 V analog supply

intended to reduce the transient noise injected into the analog

sible to the device. The connection between the beads and

the SPT7922 should not be shared with any other device.

Each power supply pin should be bypassed as closely as

possible to the device. Use 0.1

0.01

AGND and DGND are the two grounds available on the

SPT7922. These two internal grounds are isolated on the

device. The use of ground planes is recommended to achieve

return path (40 mA typical) and for the return path for all digital

output logic interfaces. AGND and DGND should be sepa-

rated from each other and connected together only at the

device through a ferrite bead.

A Schottky or hot carrier diode connected between AGND

tial power supply sequencing latch-up conditions. Using the

recommended interface circuit shown in figure 2 will provide

optimum device performance for the SPT7922.

VOLTAGE REFERENCE

The SPT7922 requires the use of two voltage references:

the bottom of the voltage reference ladder. Both voltages

are applied across an internal reference ladder resistance of

must be current limited to 20 mA maximum if a different

driving circuit is used in place of the recommended reference

circuit shown in figures 2 and 3. In addition, there are five

monitor the actual full scale input voltage of the device.

ideal values as is commonly done with standard flash

converters. When not being used, a decoupling capacitor of

.01

µF connected to AGND from each tap is recommended

to minimize high frequency noise injection.

Figure 2 - Typical Interface Circuit

- 5.2 V

COARSE

A/D

ANALOG

PRESCALER

SUCCESSIVE

INTERPOLATION

STAGE # 1

SUCCESSIVE

INTERPOLATION

STAGE # N

4

D11

D10

D9

D8

D7

D6

D5

D4

D3

D2

D1

D0

D12

IC1

(REF-03)

6

5

2

4

+ 5 V

+

VOUT

Trim

GND

VIN

1 µF

C1

.01 µF

+

-

10 k

Ω

1

32

4

8

7

6

10 k

Ω

30 k

Ω

30 k

Ω

C19

1 µF

+

+5 V

C18

.01 µF

C17

.01 µF

CLK

VIN

VFT

VST

VRT3

VRT2

VRT1

VSB

VFB

R

2R

2R

2R

2R

R

+

C16

1 µF

CLK

VIN

IC2

OP-07

C15

10 µF

C14

10 µF

+

D1

C12

.01 µF

+

(TTL)

(±2 V)

+2.5 V

-2.5 V

FB

+5 V

AGND

DGND

-5.2 V

(Analog)

(Analog)

17

24

21

22

23

25

26

27

28

18

31

19

30

20

29

16

32

1

15

(OVERRANGE)

(MSB)

(LSB)

14

13

12

11

10

9

8

7

6

5

4

3

2

C13

.01 µF

R1

100

Ω

± 2.5 V Max

C2

.01 µF

C3

.01 µF

C4

.01 µF

C5

.01 µF

C6

.01 µF

C7

.01 µF

C8

.1 µF

C9

.1 µF

C10

C11

Notes to prevent latch-up due to power sequencing:

1) D1 = Schottky or hot carrier diode, P/N IN5817.

2) FB = Ferrite bead, Fair Rite P/N 2743001111

to be mounted as close to the device as possible. The ferrite bead to the ADC

connection should not be shared with any other device.

3) C1-C13 = Chip cap (recommended) mounted as close to the device's pin as

possible.

4) Use of a separate supply for VCC and DVCC is not recommended.

5) R1 provides current limiting to 45 mA.

6) C8, C9, C10 and C11 should be ten times larger than C12 and C13.

7) C10 = C11 = 0.1 µF cap in parallel with a 4.7 µF cap.