CDK1307DILP40 datasheet(13/15 Pages) CADEKA

13 / 15 page

www.cadeka.com

Data Sheet

The quality of the input clock is extremely important for

high-speed, high-resolution ADCs. The contribution to SNR

from clock jitter with a full scale signal at a given frequency

is shown in the equation below:

SNRjitter = 20 • log (2 • π • FIN •

εt)

where FIN is the signal frequency, and

εt is the total rms

jitter measured in seconds. The rms jitter is the total of all

jitter sources including the clock generation circuitry, clock

distribution and internal ADC circuitry.

For applications where jitter may limit the obtainable per-

formance, it is of utmost importance to limit the clock

jitter. This can be obtained by using precise and stable

clock references (e.g. crystal oscillators with good jitter

specifications) and make sure the clock distribution is well

controlled. It might be advantageous to use analog power

and ground planes to ensure low noise on the supplies

to all circuitry in the clock distribution. It is of utmost im-

portance to avoid crosstalk between the ADC output bits

and the clock and between the analog input signal and

the clock since such crosstalk often results in harmonic

distortion.

The jitter performance is improved with reduced rise and

fall times of the input clock. Hence, optimum jitter per-

formance is obtained with LVDS or LVPECL clock with fast

edges. CMOS and sine wave clock inputs will result in

slightly degraded jitter performance.

If the clock is generated by other circuitry, it should be re-

timed with a low jitter master clock as the last operation

before it is applied to the ADC clock input.

Digital Outputs

Digital output data are presented on parallel CMOS form.

The voltage on the OVDD pin set the levels of the CMOS

outputs. The output drivers are dimensioned to drive a

wide range of loads for OVDD above 2.25V, but it is rec-

ommended to minimize the load to ensure as low transient

switching currents and resulting noise as possible. In ap-

plications with a large fanout or large capacitive loads, it

is recommended to add external buffers located close to

the ADC chip.

The timing is described in the Timing Diagram section.

Note that the load or equivalent delay on CK_EXT always

should be lower than the load on data outputs to ensure

sufficient timing margins.

The digital outputs can be set in tristate mode by setting

the OE_N signal high.

The CDK1307 employs digital offset correction. This means

that the output code will be 4096 with shorted inputs.

However, small mismatches in parasitics at the input can

cause this to alter slightly. The offset correction also re-

sults in possible loss of codes at the edges of the full scale

range. With no offset correction, the ADC would clip in one

end before the other, in practice resulting in code loss at

the opposite end. With the output being centered digitally,

the output will clip, and the out of range flags will be set,

before max code is reached. When out of range flags are

set, the code is forced to all ones for over-range and all

zeros for under-range.

Data Format Selection

The output data are presented on offset binary form

when DFRMT is low (connect to OVSS). Setting DFRMT

high (connect to OVDD) results in 2’s complement output

format. Details are shown in Table 1 on page 14.

The data outputs can be used in three different configurations.

Normal mode:

All 13-bits are used. MSB is D_12 and LSB is D_0. This

mode gives optimum performance due to reduced quanti-

zation noise.

12-bit mode:

The LSB is left unconnected such that only 12 bits are

used. MSB is D_12 and LSB is D_1. This mode gives slightly

reduced performance, due to increased quantization noise.

Reduced full scale range mode:

The full scale range is reduced from 2Vpp to 1Vpp which is

equivalent to 6dB gain in the ADC frontend. MSB is D_11

and LSB is D_0. Note that the codes will wrap around

when exceeding the full scale range, and that out of range

bits should be used to clamp output data. See section

Reference Voltages for details. This mode gives slightly

reduced performance.

CDK1307DILP40 Datasheet(PDF) 13 Page - Cadeka Microcircuits LLC.

CDK1307DILP40 Datasheet(HTML) 13 Page - Cadeka Microcircuits LLC.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Datasheet Download

Link URL