| Electronic Components Datasheet Search |
|
MAX2829 Datasheet(PDF) 29 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX2829 Datasheet(HTML) 29 Page - Maxim Integrated Products |
|
29 / 39 page ![]() Single-/Dual-Band 802.11a/b/g World-Band Transceiver ICs ______________________________________________________________________________________ 29 Shutdown Mode Shutdown mode is achieved by driving SHDN low. In shutdown mode, all circuit blocks are powered down, except for the serial interface. While the device is in shutdown, the values of the serial interface registers are maintained and can be changed as long as VCC (pin 25) is applied. SPI Reset By driving RXENA and TXENA high while setting SHDN low, all circuit blocks are powered down, as in shut- down mode. However, in SPI reset mode, all registers are returned to their default states. It is recommended to reset the SPI and all registers at the start of power-up to ensure that the registers are set to the correct values (see Table 9). Standby Mode To place the device in standby mode, set SHDN high and RXENA and TXENA low. This mode is mainly used to enable the frequency synthesizer block while the rest of the device is powered down. In this mode, various blocks in the system can be selectively turned on or off according to the standby register table (Table 10). Receive (Rx) Mode To place the device in Rx mode, set RXENA high. All receiver blocks are enabled in this mode. Transmit (Tx) Mode To place the device in Tx mode, set TXENA high. All transmitter blocks are enabled in this mode. Tx/Rx Calibration Mode The MAX2828/MAX2829 feature Tx/Rx calibration modes to detect I/Q imbalances and transmit LO leak- age. In the Tx calibration mode, the LO leakage cali- bration is done only for the LO leakage signal that is present at the center frequency of the channel (i.e., in the middle of the OFDM or QPSK spectrum). The LO leakage calibration includes the effect of all DC offsets in the entire baseband paths of the I/Q modulator, and also includes direct leakage of the LO to the I/Q modu- lator output. The transmitter LO leakage and sideband-detector out- put is taken at the receiver I- or Q-channel output dur- ing this calibration phase. During Tx LO leakage and I/Q imbalance calibration, a sine and cosine signal (f = fTONE) is input to the base- band I/Q Tx pins from the baseband IC. At the LO leak- age and sideband-detector output, the LO leakage corresponds to the signal at fTONE and the sideband suppression corresponds to the signal at 2 x fTONE. The output power of these signals vary 2dB for 1dB of variation in the LO leakage and unwanted sideband levels. To calibrate the Tx path, first set the power- detector gain to 8dB (Table 14). Adjust the DC offset of the baseband inputs to minimize the signal at fTONE (LO leakage). Then, adjust the baseband input relative magnitude and phase offsets to reduce the signal at 2 x fTONE. If required, calibration can be done with higher LO leakage and sideband-detector gain settings to decrease LO leakage and increase image suppression. After calibrating the transmitter, receiver calibration can be done. In Rx calibration mode, the calibrated Tx RF signal is internally routed to the Rx downconverter inputs. In this loopback calibration mode, the voltage regulator must be able to source 350mA total since both Tx and Rx are turned on simultaneously. RF Synthesizer Programming in 5GHz Mode In the 5GHz mode, the RF frequency synthesizer cov- ers a 4.9GHz to 5.9GHz range. To achieve this large tuning range while maintaining excellent noise perfor- mance, the 1GHz band is divided into sub-bands within which the VCO is tuned. The selection of the appropri- ate VCO sub-band is done automatically by a finite state machine (FSM). The PLL settling time is approxi- mately 300µs for a change of 1GHz in the channel fre- quency. A faster PLL settling can be achieved by overriding the FSM and manually programming the VCO sub-band. Automatic VCO Sub-Band Selection By enabling this band-selection mode, only 1 bit needs to be programmed to start the frequency acquisition. The FSM will automatically stop after it selects the cor- rect VCO sub-band, and after the PLL has locked. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |