0.620 M A X

(15.75)

PA CK A GE OUTLINE

Dimensions shown in inches and (mm)

DIM ENSIONS

Inch

mm

0.145

(3.68)

0.010

(0.254)

0.600

(15.240)

0.125 M IN

(3.18)

0.414 M A X

(35.92)

0.052

(1.32)

0.020

(0.51)

15

14

28

PIN 1

DOT

BOTTOM

V IEW

O R D E R I N G I N F O R MAT I O N

PIN

FUNCTION

PIN

FUNCTION

1

D8,o/DB2

28

DB9/DB1

2

DBn(M SB)/DB3

27

DB8/DB0

3

A o

26

DB7

4

R/C

25

DB6

5

GROUND

24

DB5

6

V LOGIC

23

084

7

V EE

22

STS(STA TUS)

8

M UX A DDRESS A 2

21

GA IN

9

M UX A DDRESS A 1

20

OFFSET

10

M UX A DDRESS A 0

19

V cc

11

INPUT CH 1

18

INPUT CH 5

12

INPUT CH 2

17

INPUT CH 6

13

INPUT CH 3

16

INPUT CH 7

14

INPUT CH 4

15

INPUT CH 8

System

Full Scale

M odel

Input

A ccuracy

T.C.

Temp.

M IL

Number1

Range

(% FSR)

(ppm/ºC)

Range

Screening

HS 94XXJ

±0.025

50.0

0ºC to +70ºC

—

HS 94XXK

±0.012

20.0

0ºC to +70ºC

—

HS 94XXS

SEE

±0.025

50.0

–55ºC to +125ºC

—

HS 94XXT

NOTE1

±0.012

25.0

–55ºC to +125ºC

—

HS 94XXS/B

±0.025

50.0

–55ºC to +125ºC

883C

HS 94XXT/B

±0.012

25.0

–55ºC to +125ºC

883C

PIN A SSIGNM ENTS

A BSOLUTE M A XIM UM RA TINGS

0 to +16.5V

0 to –16.5V

0 to +7V

Common GND

Power Dissipation

1.3W

Lead Temperature, Soldering

300ºC, 10Sec

M aximum Input V oltage

M inimum Input V oltage.

A nalog Input M aximum Current

25mA

M ODEL

INPUT

SUFFIX

RA NGE

10

0 to +10V

11

±5V

12

±10V

A dd letter suffix as required above

HS 94XX

NOTES

1.

STA BILITY

Linearity (ppm/ºC max)

±0.5

±0.5

±0.25

±0.25

Unipolar Offset (ppm/ºC max)

±10

±5

±25

±20

Bipolar Offset (ppm/ºC max)

±25

±20

±25

±20

Gain (Scale Factor)(ppm/ºC max)

TEM PERA TURE RA NGE

Operating

0º to +70ºC

–55ºC to +125ºC

-55ºC to +125ºC

Storage

–25ºC to +85ºC

–65ºC to +150ºC

-55ºC to +125ºC

NOTES

1 For J and K models, positive analog input voltage should not exceed V CC –4 volts. Exceeding \/CC –4 volts can cause an OFF channel to be turned ON. Negative

input voltages and input voltages for S and T models may go to supply voltages. Input voliages exceeding these values will not result in permanent damage as long

as the absolute maximum ratings are not exceeded. 2. 1 K pullup to + 5V recommended for M A 0-MA2 when driven by TTL 3.Maximum change over rated supply

voltage. 4. Externally adjustable to zero. See A pplications Information.

* Specifications same as HS 9410J

HS9410 SERIES