Notes

1. guaranteed by qualification test and/or analysis. Not an in-line test.

2. Converter will shut down above approximately 45 volts input but will be

undamaged and will restart when voltage drops into normal range.

3. Recovery time is measured from application of the transient to the point at which

4. Tested on release from inhibit.

5. No affect on dc performance.

SINgLE OuTPuT MOdELS

MFL283R3S

MFL2805S

MFL2812S

uNITS

PaRaMETER

CONdITIONS

MIN

TYP

MaX

MIN

TYP

MaX

MIN

TYP

MaX

OuTPuT VOLTagE

3.21

3.30

3.39

4.87

5.00

5.13

11.76 12.00 12.24

V

OuTPuT CuRRENT

0

—

12.12

0

—

10

0

—

5

a

OuTPuT POWER

0

—

40

0

—

50

0

—

60

W

OuTPuT RIPPLE

—

10

35

—

15

35

—

30

75

mV p-p

10 kHZ - 2 MHZ

—

10

50

—

30

50

—

45

100

LINE REguLaTION

—

0

20

—

0

20

—

0

20

mV

LOad REguLaTION

NO LOad TO FuLL

—

—

40

—

—

20

—

—

20

mV

INPuT VOLTagE

CONTINuOuS

16

28

40

16

28

40

16

28

40

V

NO LOad TO FuLL

—

—

80

—

—

80

—

—

80

V

INPuT CuRRENT

NO LOad

—

70

100

—

70

120

—

50

100

INHIBITEd–INH1

—

9

14

—

9

14

—

9

14

ma

INHIBITEd–INH2

—

35

70

—

35

70

—

35

70

INPuT RIPPLE CuRRENT

10 kHz - 10 MHz

—

15

50

—

15

50

—

15

50

ma p-p

EFFICIENCY

73

76

—

77

80

—

83

86

—

%

71

—

—

75

_

81

LOad FauLT

POWER dISSIPaTION

—

12.5

16

—

12.5

18

—

10

16

W

—

1.5

6

—

1.5

4

—

1.5

4

ms

TRaNSIENT

—

200

300

—

250

350

—

450

600

mV pk

50% - 100% - 50%

—

1.5

3.0

—

1.5

3.0

—

1.5

3.0

ms

TRaNSIENT

—

250

300

—

250

300

—

250

400

mV pk

16 - 40 - 16

RECOVERY

—

200

600

—

200

300

—

200

300

µs

dELaY

—

3.5

6

—

3.5

6

—

3.5

6

ms

—

0

25

—

0

25

—

0

25

mV pk

—

—

1000

—

—

1000

—

—

1000

µF

MFL single and dual dc-dc converters

28 VoLt input - 65 Watt

www.craneae.com/interpoint

Page 7 of 14

MFL Rev ad - 2016.02.19

Crane Aerospace & Electronics Power Solutions