STLUX datasheet(84/126 Pages) STMICROELECTRONICS

84 / 126 page

Electrical characteristics

STLUX

84/126

DocID027870 Rev 1

12.2

Absolute maximum ratings

Stresses above those listed as 'absolute maximum ratings' may cause permanent damage

to the device. This is a stress rating only and functional operation of the device under these

conditions is not implied. Exposure to maximum rating conditions for extended periods may

affect the device reliability.

Table 67. Voltage characteristics

Symbol

Ratings

Min.

Max.

Unit

VDDX - VSSX Supply voltage(1)

1. All power VDDX (VDD, VDDA) and ground VSSX (VSS, VSSA) pins must always be connected to the external

power supply.

-0.3

6.5

VIN

Input voltage on any other pin(2)

2. IINJ(PIN) must never be exceeded. This is implicitly insured if VIN maximum is respected. If VIN maximum

cannot be respected, the injection current must be limited externally to the IINJ(PIN) value. A positive

injection is induced by VIN > VDD while a negative injection is induced by VIN < VSS.

VSS - 0.3

VDD + 0.3

VDD - VDDA Variation between different power pins

VSS - VSSA

Variation between all the different

ground pins(3)

3. VSS and VSSA signals must be interconnected together with a short wire loop.

VESD

Electrostatic discharge voltage

Refer to absolute maximum ratings (electrical

sensitivity) in Section 11.4.1 on page 93

Table 68. Current characteristics

Symbol

Ratings

Max.(1)

1. Data based on characterization results, not tested in production.

Unit

IVDDX

Total current into VDDX power lines(2)

2. All power VDDX (VDD, VDDA) and ground VSSX (VSS, VSSA) pins must always be connected to the external

power supply.

100

IVSSX

Total current out of VSSX power lines(2)

100

IIO

Output current sunk by any I/Os and control pin

Ref. to Table 82 on

page 100

Output current source by any I/Os and control pin

IINJ(PIN)(3), (4)

3. IINJ(PIN) must never be exceeded. This is implicitly insured if VIN maximum is respected. If VIN maximum

cannot be respected, the injection current must be limited externally to the IINJ(PIN) value. A positive

injection is induced by VIN > VDD while a negative injection is induced by VIN < VSS.

4. Negative injection disturbs the analog performance of the device.

Injected current on any pin

±4

IINJ(TOT)(3), (4), (5)

5. When several inputs are submitted to a current injection, the maximum

IINJ(PIN) is the absolute sum of the

positive and negative injected currents (instantaneous values). These results are based on

characterization with

IINJ(PIN) maximum current injection on four I/O port pins of the device.

Sum of injected currents

±20

STLUX Datasheet(PDF) 84 Page - STMicroelectronics

STLUX Datasheet(HTML) 84 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL