AD9520-1SLASHPCBZ datasheet(73/80 Pages) AD

73 / 80 page

Data Sheet

AD9520-1

Rev. B | Page 73 of 80

Reg.

Addr.

(Hex) Bits

Name

Description

0x195 [7:3]

Unused

Unused.

Channel 1 power-down

Channel 1 powers down.

0: normal operation (default).

1: powered down. (Setting this bit puts OUT3/OUT3, OUT4/OUT4, and OUT5/OUT5 into safe

power-down mode.)

Channel 1 direct-to-output

Connects OUT3, OUT4, and OUT5 to Divider 1 or directly to VCO or CLK.

0: OUT3, OUT4, and OUT5 are connected to Divider 1 (default).

1: If Register 0x1E1[1:0] = 10b, the VCO is routed directly to OUT3, OUT4, and OUT5.

If Register 0x1E1[1:0] = 00b, the CLK is routed directly to OUT3, OUT4, and OUT5.

If Register 0x1E1[1:0] = 01b, there is no effect.

Disable Divider 1 DCC

Duty-cycle correction function.

0: enables duty-cycle correction (default).

1: disables duty-cycle correction.

0x196 [7:4]

Divider 2 low cycles

Number of clock cycles (minus 1) of the divider input during which the divider output stays low.

A value of 0x1 means that the divider is low for two input clock cycles (default: 0x1).

[3:0]

Divider 2 high cycles

Number of clock cycles (minus 1) of the divider input during which the divider output stays high.

A value of 0x1 means that the divider is high for two input clock cycles (default: 0x1).

0x197 7

Divider 2 bypass

Bypasses and powers down the divider; routes input to divider output.

0: uses divider (default).

1: bypasses divider.

Divider 2 ignore SYNC

Ignores SYNC.

0: obeys chip-level SYNC signal (default).

1: ignores chip-level SYNC signal.

Divider 2 force high

Forces divider output to a specific state. This requires that ignore SYNC also be set. Note that

this bit has no effect if the channel divider is bypassed, but the driver polarity can still be reversed.

0: divider output is forced to low (default).

1: divider output is forced to the setting stored in Bit 4 of this register.

Divider 2 start high

Selects clock output to start high or start low.

0: starts low (default).

1: starts high.

[3:0]

Divider 2 phase offset

Phase offset (default: 0x0).

0x198 [7:3]

Unused

Unused.

Channel 2 power-down

Channel 2 powers down.

0: normal operation (default).

1: powered down. (Setting this bit puts OUT6/OUT6, OUT7/OUT7, and OUT8/OUT8 into safe

power-down mode.)

Channel 2 direct-to-output

Connects OUT6, OUT7, and OUT8 to Divider 2 or directly to VCO or CLK.

0: OUT6, OUT7, and OUT8 are connected to Divider 2 (default).

1: If Register 0x1E1[1:0] = 10b, the VCO is routed directly to OUT6, OUT7, and OUT8.

If Register 0x1E1[1:0] = 00b, the CLK is routed directly to OUT6, OUT7, and OUT8.

If Register 0x1E1[1:0] = 01b, there is no effect.

Disable Divider 2 DCC

Duty-cycle correction function.

0: enables duty-cycle correction (default).

1: disables duty-cycle correction.

0x199 [7:4]

Divider 3 low cycles

Number of clock cycles (minus 1) of the divider input during which the divider output stays low.

A value of 0x0 means that the divider is low for one input clock cycle (default: 0x0).

[3:0]

Divider 3 high cycles

Number of clock cycles (minus 1) of the divider input during which the divider output stays high.

A value of 0x0 means that the divider is high for one input clock cycle (default: 0x0).

AD9520-1/PCBZ Datasheet(PDF) 73 Page - Analog Devices

AD9520-1/PCBZ Datasheet(HTML) 73 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

Datasheet Download

Link URL