AD9739-R2-EBZ datasheet(33/50 Pages) AD

33 / 50 page

Data Sheet

AD9739

Rev. E | Page 33 of 50

increase the effective range of the delay line to ensure a

DCI_DEL value that falls within a reasonable guard band.

In some situations, rotating the phase alone may not be

sufficient to create the conditions necessary for the data receiver

to lock. This is likely due to a particular misalignment of clock

edges within the device that can occur after power up or reset at

clock rates below 1.6 GHz. In these situations, it is necessary to

power down the device by taking the following steps:

Set the four power-down bits in Register 0x01

(Register 0x01 = 0x33).

Reset the power-down bits to 0 (Register 0x01 = 0x00)

Follow the start-up sequence, including possible phase

rotation, as described previously.

These three steps may need to be initiated multiple times

to achieve a successful lock.

LVDS Driver and Receiver Input

The AD9739 features a LVDS-compatible driver and receivers.

The LVDS driver output used for the DCO and SYNC_OUT

signal includes an equivalent 200 Ω source resistor that limits its

nominal output voltage swing to ±200 mV when driving a

100 Ω load. The DCO output driver can be powered down via

DCO_N

VSS

VDD33

DCO_P

V+

V–

100

Ω

VCM

100

Ω

ESD

Figure 44. Equivalent LVDS Output

VSS

VDD33

DCI_P

DBx[13:0]P

DCI_N

DBx[13:0]N

100

Ω

ESD

Figure 45. Equivalent LVDS Input

The LVDS receivers include 100 Ω termination resistors, as

shown in Figure 45. These receivers meet the IEEE-1596.3-1996

reduced swing specification (with the exception of input hysteresis,

which cannot be guaranteed over all process corners). Figure 46

and Figure 47 show an example of nominal LVDS voltage levels

seen at the input of the differential receiver with resulting common-

mode voltage and equivalent logic level. The LVDS receivers

can be powered down via Register 0x01, Bit 4.

LVDS INPUTS

(NO FAIL-SAFE)

LVDS

RECEIVER

GND

100

Ω

VP,N

VCOM

= (VP + VN)/2

LOGIC BIT

EQUIVALENT

EXAMPLE

1.4V

1.0V

0.4V

–0.4V

LOGIC 1

LOGIC 0

Figure 46. LVDS Data Input Levels

100

Ω

100

Ω

100

Ω

VDD33 = 3.3V

LVDS_1

LVDS_N

LVDS_2

VP = 1.4V

R1 = 4.75 × 100/N

R2 = 2.50 × 100/N

Figure 47. Resistor Network to Bias Unused LVDS Data Inputs

The AD9739 LVDS inputs do not include fail-safe capability.

Any unused data input pins should be biased with an external

network or static driver. Figure 47 shows an external biasing

network that can be used to place unused data bits into a known

state. The resistor values for R1 and R2 are selected to establish

a VP and VN of 1.4 V and 1.0 V, respectively, depending on the

number of unused digital inputs, N.

AD9739-R2-EBZ Datasheet(PDF) 33 Page - Analog Devices

AD9739-R2-EBZ Datasheet(HTML) 33 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

Datasheet Download

Link URL