MPC8560CPXAPDB datasheet(38/108 Pages) FREESCALE

38 / 108 page

MPC8560 Integrated Processor Hardware Specifications, Rev. 3.1

Freescale Semiconductor

Local Bus

Local bus clock to data valid for

LAD/LDP

TSEC2_TXD[6:5] = 00

tLBKHOV2

—

2.2

4, 8

TSEC2_TXD[6:5] = 11

(default)

3.7

Local bus clock to address valid for

LAD, and LALE

TSEC2_TXD[6:5] = 00

tLBKHOV3

—

2.3

4, 8

TSEC2_TXD[6:5] = 11

(default)

3.8

Output hold from local bus clock

(except LAD/LDP and LALE)

TSEC2_TXD[6:5] = 00

tLBKHOX1

0.7

—

4, 8

TSEC2_TXD[6:5] = 11

(default)

1.6

Output hold from local bus clock for

LAD/LDP

TSEC2_TXD[6:5] = 00

tLBKHOX2

0.7

—

4, 8

TSEC2_TXD[6:5] = 11

(default)

1.6

Local bus clock to output high

Impedance (except LAD/LDP and

LALE)

TSEC2_TXD[6:5] = 00

tLBKHOZ1

—

2.5

7, 9

TSEC2_TXD[6:5] = 11

(default)

3.8

Local bus clock to output high

impedance for LAD/LDP

TSEC2_TXD[6:5] = 00

tLBKHOZ2

—

2.5

7, 9

TSEC2_TXD[6:5] = 11

(default)

3.8

Notes:

1.The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state)

(reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example,

tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock

reference (K) goes high (H), in this case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the

tLBK clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time.

2.All timings are in reference to LSYNC_IN for DLL enabled mode.

3.Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew measured between

complementary signals at OVDD/2.

4.All signals are measured from OVDD/2 of the rising edge of LSYNC_IN for DLL enabled to 0.4 × OVDD of the signal

in question for 3.3-V signaling levels.

5.Input timings are measured at the pin.

6.The value of tLBOTOT is defined as the sum of 1/2 or 1 ccb_clk cycle as programmed by LBCR[AHD], and the number

of local bus buffer delays used as programmed at power-on reset with configuration pins TSEC2_TXD[6:5].

7.For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current

delivered through the component pin is less than or equal to the leakage current specification.

8.Guaranteed by characterization.

9.Guaranteed by design.

Table 30. Local Bus General Timing Parameters - DLL Enabled (continued)

Parameter

POR Configuration

Symbol 1

Min

Max

Unit

Notes

MPC8560CPXAPDB Datasheet(PDF) 38 Page - Freescale Semiconductor, Inc

MPC8560CPXAPDB Datasheet(HTML) 38 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL