| Electronic Components Datasheet Search |
|
S32Z2 Datasheet(PDF) 49 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
S32Z2 Datasheet(HTML) 49 Page - NXP Semiconductors |
|
49 / 155 page ![]() Table 19. Aurora Pads...continued Symbol Description Min Typ Max Unit Condition Spec Number at any point on Tline ) RTERM_AURORA Internal termination resistance 80 100 130 Ohm enabled — VSLEW_AURORA Differential output slew rate — 30 50 ps / 200mV max fAURORA — TSTARTUP_ AURORA Transmitter startup time (assertion of ipp_obe to common mode settling of differential output) — — 500 ns — — TEYE_AURORA Valid data region ( Including PLL Jitter for Aurora ) 5 0.55 — — UI max fAURORA — VOH_AURORA Transmitter output high indicator 6 VDD_IO/ 2 + 0.2 — — V 100Ω termination at receiver end — VOL_AURORA Transmitter output low indicator 6 — — VDD_IO/ 2 - 0.2 V 100Ω termination at receiver end — PAD_P_BIAS Pad_p voltage output level when Tx disabled — — 0.6 V Ipp_obe_lv=0 Ipp_ term_en_lv=0 — PAD_N_BIAS Pad_n voltage output level when Tx disabled 1.1 — — V Ipp_obe_lv=0 Ipp_ term_en_lv=0 — 1. When operating at max speed, there will be losses and differential output will be smaller as against DC condition. Aurora Interface Min differential swing is 400mV which is always guaranteed but the max limit is dependent on board design/ losses. For boards with negligible losses , if differential output (P-N) goes higher than 800mV (Aurora max differential input spec) , user must use “dual termination” scheme as highlighted in the Source Termination Circuit Figure to get the differential swing back within Range. The termination in the source side can be enabled through software in the transmitter pad design. Direct end termination without AC coupling is not allowed. 2. Termination scheme as shown in the End Termination Circuit Figure. Direct end termination without AC coupling is not allowed. 3. Differential output is with pre-emphasis disabled, and a 10mA output stage current. 4. Differential output is with pre-emphasis enabled, and a ~15mA avg output stage current 5. UI @ 5Gbps equals 200ps. The valid eye is expected to be > 110ps in width. ISI jitter spec is 20-30ps for the LVDS transmitter across PVT in a delay matched differential transmission line impedance of 100Ω. 6. VDD_IO maps to corresponding supply name on the device. Termination scheme as shown in “End Termination Circuit” applies to debug tool hardware and is not recommended to be placed on the PC. Source termination Circuit – Transmitter side 100 ohm termination is present inside the Tx pad and should not be placed on the PCB. Direct 100 ohm board termination not allowed between AUR_TXn_N and AUR_TXn_N (n=0,1,2,3). Source termination is only allowed through the internal termination inside LVDS Tx pad. NXP Semiconductors S32E27 S32E2 Data Sheet S32E27 All information provided in this document is subject to legal disclaimers. © 2020 - 2024 NXP B.V. All rights reserved. Product Data Sheet Rev. 5 — 3 December 2024 49 / 155 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |