| Electronic Components Datasheet Search |
|
S32Z2 Datasheet(PDF) 68 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
S32Z2 Datasheet(HTML) 68 Page - NXP Semiconductors |
|
68 / 155 page ![]() Table 27. PLL...continued Symbol Description Min Typ Max Unit Condition Spec Number fPLL_DDR_PHI0 DDR PLL PHI0 Frequency 5,8 400 — 400 MHz DDR_PLL_PHI0_CLK (1600 MT/s) — fPLL_DDR_PHI0 DDR PLL PHI0 Frequency 5,8 405 — 405 MHz DDR_PLL_PHI0_CLK (1600 MT/s), FLASH only, not applicable for DRAM. — tLOCK PLL Lock Time — — 100 us — — PER_jitter PLL Period Jitter 9,10,11,12 -23 — 23 ps fPLL_CLKIN = 40MHz, fVCO = 2GHz, 6- sigma, SSCG & Frac mode disabled — LT_jitter PLL Long Term Jitter 9,10,13 -120 — 120 ps Saturated, 6-sigma — fPLL_MOD Spread Spectrum Clock Modulation Frequency 30 — 64 KHz — — 1. This refers to spec number 1 which is shown in the figure in Aurora port specifications 2. This specification is PLL input reference clock frequency after pre-divider. 3. Same min frequency value applies for center-spread SSCG enabled as provided for center-spread SSCG disabled. 4. The frequencies are the nominal frequencies (i.e., what the PLL's VCO is configured to). 5. The max frequency in case of center-spread SSCG enabled for a modulation depth can be calculated as: Max frequency(with center-spread SSCG disabled) – (Modulation Depth(in %)/(2*100))* Max frequency (with center-spread SSCG disabled). For details, see section “Frequency modulation programming” in reference manual. 6. Duty cycle of the PLL clock when output on an external pin is given in the I/O pad specifications. 7. Part numbers with a 10th character other than E have a lower maximum frequency at TJ = 150 °C or 125 °C (13th character = M or V). See the "Ordering information" section. 8. The DDR PHY internally multiplies the PLL_DDR_PHI0 by factor of two. 9. Jitter is dependent on supply noise. Specified jitter values are valid for the FXOSC reference clock input only - not valid for FIRC reference clock input. 10. Jitter value does not apply when a PLL clock is output on an external pin. In this case, the rise and fall time variations in the I/O pad are orders of magnitude more than the PLL and SoC mux jitter contributions. 11. Jitter is dependent on the period of the PLL output clock, and the division ratio of the clock at the destination module. 12. For chip clocks that are further divided down from the PLL output clock, the jitter is multiplied by a factor of SQRT(N), where N is the ratio of the PLL output clock and destination clock periods. 13. This specification is valid when all clock sources are stable. 14.1.3 DFS The following table specifies the output frequency ranges and characteristics of the Digital Frequency Synthesizer (DFS). Table 28. DFS Symbol Description Min Typ Max Unit Condition Spec Number fDFS_CLKIN DFS Input Clock Frequency 1300 — 2400 MHz — — Table continues on the next page... NXP Semiconductors S32E27 S32E2 Data Sheet S32E27 All information provided in this document is subject to legal disclaimers. © 2020 - 2024 NXP B.V. All rights reserved. Product Data Sheet Rev. 5 — 3 December 2024 68 / 155 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |