ATmega162 datasheet(87/324 Pages) ATMEL

87 / 324 page

2513K–AVR–07/09

ATmega162/V

General Interrupt Flag

• Bit 7 – INTF1: External Interrupt Flag 1

When an edge or logic change on the INT1 pin triggers an interrupt request, INTF1 becomes set

(one). If the I-bit in SREG and the INT1 bit in GICR are set (one), the MCU will jump to the corre-

sponding Interrupt Vector. The flag is cleared when the interrupt routine is executed.

Alternatively, the flag can be cleared by writing a logical one to it. This flag is always cleared

when INT1 is configured as a level interrupt.

• Bit 6 – INTF0: External Interrupt Flag 0

When an edge or logic change on the INT0 pin triggers an interrupt request, INTF0 becomes set

(one). If the I-bit in SREG and the INT0 bit in GICR are set (one), the MCU will jump to the corre-

sponding Interrupt Vector. The flag is cleared when the interrupt routine is executed.

Alternatively, the flag can be cleared by writing a logical one to it. This flag is always cleared

when INT0 is configured as a level interrupt.

• Bit 5 – INTF2: External Interrupt Flag 2

When an event on the INT2 pin triggers an interrupt request, INTF2 becomes set (one). If the I-

bit in SREG and the INT2 bit in GICR are set (one), the MCU will jump to the corresponding

Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alternatively, the flag

can be cleared by writing a logical one to it. Note that when entering some sleep modes with the

INT2 interrupt disabled, the input buffer on this pin will be disabled. This may cause a logic

change in internal signals which will set the INTF2 flag. See “Digital Input Enable and Sleep

Modes” on page 67 for more information.

• Bit 4 – PCIF1: Pin Change Interrupt Flag 1

When a logic change on any PCINT15..8 pin triggers an interrupt request, PCIF1 becomes set

(one). If the I-bit in SREG and the PCIE1 bit in GICR are set (one), the MCU will jump to the cor-

responding Interrupt Vector. The flag is cleared when the interrupt routine is executed.

Alternatively, the flag can be cleared by writing a logical one to it.

• Bit 3 – PCIF0: Pin Change Interrupt Flag 0

When a logic change on any PCINT7..0 pin triggers an interrupt request, PCIF0 becomes set

(one). If the I-bit in SREG and the PCIE0 bit in GICR are set (one), the MCU will jump to the cor-

responding Interrupt Vector. The flag is cleared when the interrupt routine is executed.

Alternatively, the flag can be cleared by writing a logical one to it.

Bit

654

INTF1

INTF0

INTF2

PCIF1

PCIF0

–

–GIFR

Read/Write

R/W

Initial Value

ATmega162 Datasheet(PDF) 87 Page - ATMEL Corporation

ATmega162 Datasheet(HTML) 87 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL