MPC8308CVMADDA datasheet(3/88 Pages) FREESCALE

3 / 88 page

MPC8308 PowerQUICC II Pro Processor Hardware Specification, Rev. 1

Freescale Semiconductor

Electrical Characteristics

2.1.2

Power Supply Voltage Specification

Table 2 provides the recommended operating conditions for the device. Note that the values in Table 2 are

the recommended and tested operating conditions. Proper device operation outside of these conditions is

not guaranteed.

Local bus, DUART, system control and power management,

eSDHC, I2C, USB, Interrupt, Ethernet management, SPI,

Miscellaneous and JTAG I/O voltage

NVDD

–0.3 to 3.6

SERDES PHY

XCOREVDD,

XPADVDD,

SDAVDD

–0.3 to 1.26

—

eTSEC I/O Voltage

LVDD1, LVDD2

–0.3 to 2.75 or

–0.3 to 3.6

V6,8

Input voltage

DDR2 DRAM signals

MVIN

–0.3 to (GVDD + 0.3)

2, 5

DDR2 DRAM reference

MVREF

–0.3 to (GVDD + 0.3)

2, 5

eTSEC

LVIN

–0.3 to (LVDD + 0.3)

4, 5,8

Local bus, DUART, system control and power

management, eSDHC, I2C, Interrupt,

Ethernet management, SPI, Miscellaneous

and JTAG I/O voltage

OVIN

–0.3 to (NVDD + 0.3)

3, 5,7

Storage temperature range

TSTG

–55 to 150

°C—

Notes:

1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and

functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause

permanent damage to the device.

2. Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during

power-on reset and power-down sequences.

3. Caution: OVIN must not exceed NVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during

power-on reset and power-down sequences.

4. Caution: LVIN must not exceed LVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on

reset and power-down sequences.

5. (M, L, O)VIN and MVREF may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2

6. The max value of supply voltage should be selected based on the RGMII mode. The lower range applies to RGMII mode.

7. NVDD here refers to NVDDA, NVDDB,NVDDG, NVDDH, NVDDP_K from the ball map.

8. LVDD1 here refers to NVDDC and LVDD2 refers to NVDDF from the ball map

Table 2. Recommended Operating Conditions

Characteristic

Symbol

Recommended Value1

Unit

SerDes internal digital power

XCOREVDD

1.0 V ± 50 mV

SerDes internal digital power

XCOREVSS

0.0

SerDes I/O digital power

XPADVDD

1.0 V ± 50 mV

SerDes analog power for PLL

SDAVDD

1.0 V ± 50 mV

Table 1. Absolute Maximum Ratings1 (continued)

Characteristic

Symbol

Max Value

Unit

Notes

MPC8308CVMADDA Datasheet(PDF) 3 Page - Freescale Semiconductor, Inc

MPC8308CVMADDA Datasheet(HTML) 3 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

Datasheet Download

Link URL