M38B53M4-059FP datasheet(57/69 Pages) MITSUBISHI

57 / 69 page

MITSUBISHI MICROCOMPUTERS

38B5 Group

SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER

PRELIMINAR

Notice:

This

is not

a final

specification.

Some

parametric

limits

are

subject

to change.

Clock Generating Circuit

The 38B5 group has two built-in oscillation circuits. An oscillation

circuit can be formed by connecting a resonator between XIN and

XOUT (XCIN and XCOUT). Use the circuit constants in accordance with

the resonator manufacturer's recommended values. No

external resistor is needed between XIN and XOUT since a feedback

resistor exists on-chip. However, an external feedback resistor is

needed between XCIN and XCOUT.

Immediately after power on, only the XIN oscillation circuit starts

oscillating, and XCIN and XCOUT pins function as I/O ports.

qFrequency control

(1) Middle-speed mode

The internal system clock is the frequency of XIN divided by 4. After

reset, this mode is selected.

(2) High-speed mode

The internal system clock is the frequency of XIN.

(3) Low-speed mode

The internal system clock is the frequency of XCIN divided by 2.

sNote

If you switch the mode between middle/high-speed and low-speed,

stabilize both XIN and XCIN oscillations. The sufficient time is required

for the sub clock to stabilize, especially immediately after power on

and at returning from stop mode. When switching the mode between

middle/high-speed and low-speed, set the frequency on condition

that f(XIN) > 3f(XCIN).

(4) Low power consumption mode

The low power consumption operation can be realized by stopping

the main clock XIN in low-speed mode. To stop the main clock, set bit

5 of the CPU mode register to “1.” When the main clock XIN is re-

started (by setting the main clock stop bit to “0”), set enough time for

oscillation to stabilize.

By clearing furthermore the XCOUT drivability selection bit (b3) of CPU

mode register to “0,” low power consumption operation of less than

200 µA (f(XCIN) = 32 kHz) can be realized by reducing the drivability

between XCIN and XCOUT. At reset or during STP instruction execu-

tion this bit is set to “1” and a strong drivability that has an easy

oscillation start is set.

qOscillation control

(1) Stop mode

If the STP instruction is executed, the internal system clock stops at

an “H” level, and XIN and XCIN oscillators stop. Timer 1 is set to “FF16”

and timer 2 is set to “0116.”

Either XIN divided by 8 or XCIN divided by 16 is input to timer 1 as

count source, and the output of timer 1 is connected to timer 2. The

bits of the timer 12 mode register are cleared to “0.” Set the interrupt

enable bits of the timer 1 and timer 2 to disabled (“0”) before execut-

ing the STP instruction. Oscillator restarts when an external interrupt

is received, but the internal system clock is not supplied to the CPU

until timer 1 underflows. This allows time for the clock circuit oscilla-

tion to stabilize.

(2) Wait mode

If the WIT instruction is executed, the internal system clock stops at

an “H” level. The states of XIN and XCIN are the same as the state

before executing the WIT instruction. The internal system clock re-

starts at reset or when an interrupt is received. Since the oscillator

does not stop, normal operation can be started immediately after the

clock is restarted.

Fig. 68 Ceramic Resonator Circuit

Fig. 69 External Clock Input Circuit

XIN

XOUT

External oscillation circuit

VCC

VSS

open

XCIN

XCOUT

External oscillation circuit

or external pulse

open

VCC

VSS

XCIN

XCOUT

XIN

XOUT

CIN

COUT

CCIN

CCOUT

M38B53M4-059FP Datasheet(PDF) 57 Page - Mitsubishi Electric Semiconductor

M38B53M4-059FP Datasheet(HTML) 57 Page - Mitsubishi Electric Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

Datasheet Download

Link URL