LAN8741AI-EN datasheet(83/106 Pages) MICROCHIP

83 / 106 page

 2013-2015 Microchip Technology Inc.

DS00001988A-page 83

LAN8741A/LAN8741Ai

5.0

OPERATIONAL CHARACTERISTICS

5.1

Absolute Maximum Ratings*

Supply Voltage (VDDIO, VDD1A, VDD2A) (see Note 1).......................................................................... -0.5 V to +3.6 V

Digital Core Supply Voltage (VDDCR) (see Note 1) ................................................................................ -0.5 V to +1.5 V

Ethernet Magnetics Supply Voltage ......................................................................................................... -0.5 V to +3.6 V

Positive voltage on input signal pins, with respect to ground (see Note 2) ............................................... VDDIO + 2.0 V

Negative voltage on input signal pins, with respect to ground (see Note 3) ............................................................-0.5 V

Positive voltage on XTAL1/CLKIN, with respect to ground .......................................................................................3.6 V

Storage Temperature ..............................................................................................................................-55oC to +150oC

Lead Temperature Range ........................................................................................... Refer to JEDEC Spec. J-STD-020

HBM ESD Performance ........................................................................................................................ .JEDEC Class 3A

Note 1: When powering this device from laboratory or system power supplies, it is important that the absolute max-

imum ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on

their outputs when AC power is switched on or off. In addition, voltage transients on the AC power line may

appear on the DC output. If this possibility exists, it is suggested that a clamp circuit be used.

2: This rating does not apply to the following pins: XTAL1/CLKIN, XTAL2, RBIAS.

3: This rating does not apply to the following pins: RBIAS.

*Stresses exceeding those listed in this section could cause permanent damage to the device. This is a stress rating

only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Functional

operation of the device at any condition exceeding those indicated in Section 5.2, "Operating Conditions**" or any other

applicable section of this specification is not implied. Note, device signals are NOT 5.0 V tolerant unless specified oth-

erwise.

5.2

Operating Conditions**

Supply Voltage (VDDIO) ....................................................................................................................... +1.62 V to +3.6 V

Analog Port Supply Voltage (VDD1A, VDD2A) ....................................................................................... +3.0 V to +3.6 V

Digital Core Supply Voltage (VDDCR) ................................................................................................ +1.14 V to +1.26 V

Ethernet Magnetics Supply Voltage ...................................................................................................... +2.25 V to +3.6 V

Ambient Operating Temperature in Still Air (TA)........................................................................................... (see Note 1)

Note 1: 0°C to +70°C for commercial version, -40°C to +85°C for industrial version.

**Proper operation of the device is guaranteed only within the ranges specified in this section. After the device has com-

pleted power-up, VDDIO and the magnetics power supply must maintain their voltage level with ±10%. Varying the volt-

age greater than ±10% after the device has completed power-up can cause errors in device operation.

5.3

Package Thermal Specifications

Note:

Do not drive input signals without power supplied to the device.

TABLE 5-1:

PACKAGE THERMAL PARAMETERS

Parameter

Symbol

Value

Unit

Comment

Thermal Resistance

ΘJA

47.8

oC/W

Measured in still air from the die to ambient air

Junction-to-Top-of-Package

ΨJT

0.7

oC/W

Measured in still air

Note:

Thermal parameters are measured or estimated for devices in a multi-layer 2S2P PCB per JESD51.

LAN8741Ai-EN Datasheet(PDF) 83 Page - Microchip Technology

LAN8741Ai-EN Datasheet(HTML) 83 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL