ST10F276 datasheet(14/229 Pages) STMICROELECTRONICS

14 / 229 page

Introduction

ST10F276

14/229

restrictions and functional differences due to the XBUS peculiarities are present

between the classic PWM, and the new XPWM.

●

An I2C interface on the XBUS is added (see X-I2C or simply I2C interface).

●

CLKOUT function can output either the CPU clock (like in ST10F269) or a software

programmable prescaled value of the CPU clock.

●

Embedded memory size has been significantly increased (both Flash and RAM).

●

PLL multiplication factors have been adapted to new frequency range.

●

A/D Converter is not fully compatible versus ST10F269 (timing and programming

model). Formula for the convertion time is still valid, while the sampling phase

programming model is different.

Besides, additional 8 channels are available on P1L pins as alternate function: the

accuracy reachable with these extra channels is reduced with respect to the standard

Port5 channels.

●

External Memory bus potential limitations on maximum speed and maximum

capacitance load could be introduced (under evaluation): ST10F276 will probably not

be able to address an external memory at 64MHz with 0 wait states (under evaluation).

●

XPERCON register bit mapping modified according to new peripherals implementation

(not fully compatible with ST10F269).

●

Bondout chip for emulation (ST10R201) cannot achieve more than 50MHz at room

temperature (so no real time emulation possible at maximum speed).

●

Input section characteristics are different. The threshold programmability is extended to

all port pins (additional XPICON register); it is possible to select standard TTL (with up

to 500mV of hysteresis) and standard CMOS (with up to 800mV of hysteresis).

●

Output transition is not programmable.

●

CAN module is enhanced: ST10F276 implements two C-CAN modules, so the

programming model is slightly different. Besides, the possibility to map in parallel the

two CAN modules is added (on P4.5/P4.6).

●

On-chip main oscillator input frequency range has been reshaped, reducing it from 1-

25MHz down to 4-12MHz. This is a high performance oscillator amplifier, providing a

very high negative resistance and wide oscillation amplitude: when this on-chip

amplifier is used as reference for Real Time Clock module, the Power-down

consumption is dominated by the consumption of the oscillator amplifier itself. A metal

option is added to offer a low power oscillator amplifier working in the range of 4-8MHz:

this will allow a power consumption reduction when Real Time Clock is running in

Power Down mode using as reference the on-chip main oscillator clock.

●

A second on-chip oscillator amplifier circuit (32kHz) is implemented for low power

modes: it can be used to provide the reference to the Real Time Clock counter (either in

Power Down or Stand-by mode). Pin XTAL3 and XTAL4 replace a couple of VDD/VSS

pins of ST10F269.

●

Possibility to re-program internal XBUS chip select window characteristics (XRAM2 and

XFLASH address window) is added.

ST10F276 Datasheet(PDF) 14 Page - STMicroelectronics

ST10F276 Datasheet(HTML) 14 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL