MPC5604B datasheet(57/106 Pages) FREESCALE

57 / 106 page

Electrical characteristics

MPC5604B/C Microcontroller Data Sheet, Rev. 8

Freescale Semiconductor

IDDSTDBY2 CC P STANDBY2 mode current

9 Slow internal RC oscillator

(128 kHz) running

TA = 25 °C

—

100

µA

DTA =55°C

—

DTA =85°C

—

180

—

DTA = 105 °C

—

315

—

PTA = 125 °C

—

560

1700

IDDSTDBY1 CC T STANDBY1 mode

current10

Slow internal RC oscillator

(128 kHz) running

TA = 25 °C

—

µA

DTA =55°C

—

DTA =85°C

—

100

—

DTA = 105 °C

—

165

—

DTA = 125 °C

—

280

900

1 V

DD = 3.3 V ± 10% / 5.0 V ± 10%, TA = 40 to 125 °C, unless otherwise specified

2 Running consumption is given on voltage regulator supply (V

DDREG). IDDMAX is composed of three components:

IDDMAX = IDD(vdd_bv) + IDD(vdd_hv) + IDD(Vdd_hv_adc). It does not include a fourth component linked to I/Os

toggling which is highly dependent on the application. The given value is thought to be a worst case value with all

peripherals running, and code fetched from code flash while modify operation on-going on data flash. It is to be

noticed that this value can be significantly reduced by application: switch-off not used peripherals (default), reduce

peripheral frequency through internal prescaler, fetch from RAM most used functions, use low power mode when

possible.

3 Higher current may be sinked by device during power-up and standby exit. please refer to in rush current on Table 21.

4 RUN current measured with typical application with accesses on both flash and RAM.

5 Only for the “P” classification: Data and Code Flash in Normal Power. Code fetched from RAM: Serial IPs CAN and

LIN in loop back mode, DSPi as Master, PLL as system Clock (4 x Multiplier) peripherals on (eMIOS/CTU/ADC) and

running at max frequency, periodic SW/WDG timer reset enabled.

6 Data Flash Power Down. Code Flash in Low Power. RC-osc128kHz & RC-OSC 16MHz on. 10MHz XTAL clock.

FlexCAN: instances: 0, 1, 2 ON (clocked but not reception or transmission), instances: 4, 5, 6 clock gated. LINFlex:

instances: 0, 1, 2 ON (clocked but not reception or transmission), instance: 3 clock gated. eMIOS: instance: 0 ON

(16 channels on PA[0]-PA[11] and PC[12]-PC[15]) with PWM 20kHz, instance: 1 clock gated. DSPI: instance: 0

(clocked but no communication). RTC/API ON.PIT ON. STM ON. ADC ON but not conversion except 2 analogue

watchdog

7 Only for the “P” classification: No clock, RC 16MHz off, RC128kHz on, PLL off, HPvreg off, ULPVreg/LPVreg on. All

possible peripherals off and clock gated. Flash in power down mode.

8 When going from RUN to STOP mode and the core consumption is > 6 mA , it is normal operation for the main

regulator module to be kept on by the on-chip current monitoring circuit. This is most likely to occur with junction

temperatures exceeding 125 °C and under these circumstances, it is possible for the current to initially exceed the

maximum STOP specification by up to 2 mA. After entering stop, the application junction temperature will reduce to

the ambient level and the main regulator will be automatically switched off when the load current is below 6 mA.

9 Only for the “P” classification: ULPreg on, HP/LPVreg off, 32kB RAM on, device configured for minimum

consumption, all possible modules switched-off.

10 ULPreg on, HP/LPVreg off, 8kB RAM on, device configured for minimum consumption, all possible modules

switched-off.

Table 23. Low voltage power domain electrical characteristics (continued)

Symbol

Parameter

Conditions1

Value

Unit

Min

Typ

Max

MPC5604B Datasheet(PDF) 57 Page - Freescale Semiconductor, Inc

MPC5604B Datasheet(HTML) 57 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL