 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
ADT7462ACPZ-R7 Datasheet(PDF) 6 Page - ON Semiconductor |
|
|
|||||||||||||||||||||||||||||
ADT7462ACPZ-R7 Datasheet(HTML) 6 Page - ON Semiconductor |
|
|
6 / 81 page  ADT7462 http://onsemi.com 6 ELECTRICAL CHARACTERISTICS TA = TMIN to TMAX, VCC = VMIN to VMAX, unless otherwise noted. (Note 1) Parameter Unit Max Typ Min Test Conditions / Comments OPEN−DRAIN SERIAL BUS OUTPUT (SDA) Output Low Voltage, VOL IOUT = −3 mA, VCC = +3.3 V 0.4 V High Level Output Leakage Current, IOH VOUT = VCC 0.1 ±1.0 mA SERIAL BUS DIGITAL INPUTS (SDA AND SCL) Input High Voltage, VIH 2.1 V Input Low Voltage, VIL 0.8 V Hysteresis 500 mV DIGITAL INPUT LOGIC LEVELS (VID0 to VID6) AND THERM, TACH, GPIO, VR_HOT, SCSI_TERM) Input High Voltage, VIH Bit 3 and Bit 4 of Configuration Register 3 = 0 1.7 V Input Low Voltage, VIL Bit 3 and Bit 4 of Configuration Register 3 = 0 0.8 V Input High Voltage, VIH (VID0 to VID6) Bit 3 of Configuration Register 3 = 1 0.65 V Input High Voltage, VIH (THERM) Bit 4 of Configuration Register 3 = 1 2/3 VCCP1 V Input Low Voltage, VIL Bit 3 and Bit 4 of Configuration Register 3 = 1 0.4 V Hysteresis 500 mV DIGITAL INPUT CURRENTS Input High Current, IIH VIN = VCC −1.0 mA Input Low Current, IIL VIN = 0 +1.0 mA Input Capacitance (Note 3) 5.0 pF SERIAL BUS TIMING (Note 3) Clock Frequency See Figure 2 400 kHz Glitch Immunity, tSW See Figure 2 50 ns Bus Free Time See Figure 2 1.3 ms Start Setup Time, tSU;STA See Figure 2 0.6 ms Start Hold Time, tHD;STA See Figure 2 0.6 ms SCL Low Time, tLOW See Figure 2 1.3 ms SCL High Time, tHIGH See Figure 2 0.6 ms SCL, SDA Rise Time, tR See Figure 2 1000 ns SCL, SDA Fall Time, tF See Figure 2 300 ns Data Setup Time, tSU;DAT See Figure 2 100 ns Detect Clock Low Timeout Can be optionally enabled 25 ms 1. All voltages are measured with respect to GND, unless otherwise specified. Typical values are at TA = 25°C and represent the most likely parametric norm. Logic inputs accept input high voltages up to 5.0 V, even when the device is operating at supply voltages below 5.0 V. Timing specifications are tested at logic levels of VIL = 0.8 V for a falling edge and VIH = 2.0 V for a rising edge. 2. Unused digital inputs connected to GND. 3. Guaranteed by design, not production tested. 4. Note that this specification does not apply if Pin 26 (VBATT, +1.2V) is being measured in single−channel mode. See Figure 16 in the Typical Performance Characteristics section for VBATT accuracy. 5. For Pin 23 and Pin 24 configured as +1.8V or +2.5V only, restricted conditions of VCC ≥ 3.3 V and +25°C ≤ TA ≤ +125°C apply. Figure 2. Serial Bus Timing Diagram SCL SDA PS S P tSU;STO tHD;STA tSU;STA tSU;DAT tHD;DAT tHD;STA tHIGH tBUF tLOW tR tF |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
British ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
