AT90PWM2 datasheet(44/365 Pages) ATMEL

44 / 365 page

4317K–AVR–03/2013

AT90PWM2/3/2B/3B

• Bit 6 - PRPSC1: Power Reduction PSC1

Writing a logic one to this bit reduces the consumption of the PSC1 by stopping the clock to this

module. When waking up the PSC1 again, the PSC1 should be re initialized to ensure proper

operation.

• Bit 5 - PRPSC0: Power Reduction PSC0

Writing a logic one to this bit reduces the consumption of the PSC0 by stopping the clock to this

module. When waking up the PSC0 again, the PSC0 should be re initialized to ensure proper

operation.

• Bit 4 - PRTIM1: Power Reduction Timer/Counter1

Writing a logic one to this bit reduces the consumption of the Timer/Counter1 module. When the

Timer/Counter1 is enabled, operation will continue like before the setting of this bit.

• Bit 3 - PRTIM0: Power Reduction Timer/Counter0

Writing a logic one to this bit reduces the consumption of the Timer/Counter0 module. When the

Timer/Counter0 is enabled, operation will continue like before the setting of this bit.

• Bit 2 - PRSPI: Power Reduction Serial Peripheral Interface

Writing a logic one to this bit reduces the consumption of the Serial Peripheral Interface by stop-

ping the clock to this module. When waking up the SPI again, the SPI should be re initialized to

ensure proper operation.

• Bit 1 - PRUSART0: Power Reduction USART0

Writing a logic one to this bit reduces the consumption of the USART by stopping the clock to

this module. When waking up the USART again, the USART should be re initialized to ensure

proper operation.

• Bit 0 - PRADC: Power Reduction ADC

Writing a logic one to this bit reduces the consumption of the ADC by stopping the clock to this

module. The ADC must be disabled before using this function. The analog comparator cannot

use the ADC input MUX when the clock of ADC is stopped.

8.7

Minimizing Power Consumption

There are several issues to consider when trying to minimize the power consumption in an AVR

controlled system. In general, sleep modes should be used as much as possible, and the sleep

mode should be selected so that as few as possible of the device’s functions are operating. All

functions not needed should be disabled. In particular, the following modules may need special

consideration when trying to achieve the lowest possible power consumption.

8.7.1

Analog to Digital Converter

If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be dis-

abled before entering any sleep mode. When the ADC is turned off and on again, the next

conversion will be an extended conversion. Refer to “CROSS REFERENCE REMOVED” for

details on ADC operation.

8.7.2

Analog Comparator

When entering Idle mode, the Analog Comparator should be disabled if not used. When entering

ADC Noise Reduction mode, the Analog Comparator should be disabled. In other sleep modes,

the Analog Comparator is automatically disabled. However, if the Analog Comparator is set up

to use the Internal Voltage Reference as input, the Analog Comparator should be disabled in all

sleep modes. Otherwise, the Internal Voltage Reference will be enabled, independent of sleep

AT90PWM2 Datasheet(PDF) 44 Page - ATMEL Corporation

AT90PWM2 Datasheet(HTML) 44 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL