PCD6003 datasheet(20/96 Pages) PHILIPS

20 / 96 page

2001 Apr 17

Philips Semiconductors

Product speciﬁcation

Digital telephone answering machine chip

PCD6003

10 THE MICROCONTROLLER

The embedded MS80C51 microcontroller controls the

Digital Telephone Answering Machine (DTAM) chip by

means of Special Function Registers (SFRs). SFRs are

defined for the blocks MCB, TICB, PCON, DSP, I2C-bus,

ports P1, P3 and P4, MA, MSK and ANA (the analog

blocks). All of these (except SFR PCON) are shown in the

block diagram in Fig.1. The architecture of the

microcontroller itself and the interface to these blocks are

described in this chapter.

10.1

Microcontroller architecture

The microcontroller architecture and its environment is

shown in Fig.7.

The microcontroller has some application-specific

peripherals such as the I2C-bus, Watchdog Timer (WD),

P1, P3, P4, MCB, External Interface with MA port, SFRs of

the DSP block, the TICB and the ANA block. Most of these

functions and SFRs are located in the Application Specific

Function block (ASF), see Fig.7.

The 80C51 core contains the 80C51 standard functions

such as Timer 0 and Timer 1, power-down/idle states and

a 15 vector dual-level interrupt controller INT15L2.

Furthermore, the microcontroller contains the Metalink

enhanced hooks protocol which enables Metalink

emulation via ALE, PSEN, EA, P0 and P2. The external

program memory access is done via the standard Ports P0

and P2. Connection of external flash memory is done via

the P4, P0 and P2 I/O pads. The microcontroller Clock

Driver (CD) has no clock divider, which means that the

microcontroller operates on 6 microcontroller_CLK clocks

per machine cycle.

The 80C51 has a few basic modes of operation: Reset,

Normal, Metalink, Test (various) Idle and Power-down.

Entering the Metalink mode can be done via inputs ALE

and EA during a reset.

The Idle mode can be entered by setting the IDL bit in the

PCON register. Leaving the Idle mode can be done via a

master reset (RSTIN), any external interrupt, a

DSP_event, TIME_event or RTC_event, Timer 0 and

Timer 1, I2C-bus interrupt, MSK_event or FS_event; if

these interrupts are enabled.

The Power-down mode can be entered by setting the

PD bit in PCON. The power-down logic of the

microcontroller will turn all microcontroller clocks off.

The TIME_event, DSP_event, RTC_event and

EX2 to EX6 are mixed with EX0 (see Fig.10) and therefore

make use of the standard wake-up circuitry of the 80C51.

These interrupts should be active for more than 6 clocks

(read, modify, write of IRQ1 takes 1 instruction) to

guarantee the interrupt for the microcontroller.

Setting the PD bit of PCON after setting the system-off bit

of SPCON, will trigger the analog section to turn off the

oscillator and therefore the whole chip. In order to keep

static supply currents minimal, it is advised to switch off the

digital-to-analog part of the CODECs before going in this

system-off mode. Wake-up from system-off can be done

via a RSTIN or an external interrupt EX0 to EX6 (if the EX0

interrupt is enabled) or EX1 (if the EX1 interrupt is

enabled). A wake-up from system-off will always reset the

PCD6003. The EX interrupt condition should last more

than 4096 + 64 + 4 clocks to be sure that the interrupt is

handled when entering the normal mode. If the interrupt is

shorter the microcontroller will only enter the normal mode

after the reset is gone.

10.2

Memory mapping

The memory map of the 80C51 is shown in Fig.8.

In addition to all the SFRs, the microcontroller has

128 bytes of directly addressable (DATA) memory,

128 bytes of indirectly addressable (IDATA) memory and

512 bytes of AUX RAM, the on-chip ‘MOVX’ addressable

(XDATA) memory. On-chip XDATA memory access can

be disabled by setting the ARD bit in PCON to logic 1. The

internal 32-kbyte ROM of microcontroller program (CODE)

memory can be accessed when EA is set to logic 1.

Via Ports P0, MA, P2 and P4 it is possible to access up to

512 kbytes of external speech data memory stored in a

parallel flash memory. A CAD flash memory can also be

mapped in this area. A serial (SPI or Microwire compatible)

flash memory can be connected to P4 which is controlled

by the MCB. Up to 64 kbytes of program (CODE) memory

can be connected to the P0, P2 and PSEN pads. This can

be any external program memory (like the MON51 target

debug ROM) if EA is logic 0.

When the EAM SFR bit (P4CFG.5) is logic 0 (default after

reset), the XRAM-mapped control registers can only be

accessed if P4.3 is logic 1. Otherwise, XRAM addressing

is independent of the value of the P4.3 SFR bit.

PCD6003 Datasheet(PDF) 20 Page - NXP Semiconductors

PCD6003 Datasheet(HTML) 20 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

Datasheet Download

Link URL