XRT83SL34IV datasheet(11/80 Pages) EXAR

11 / 80 page

XRT83SL34

QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR

PRELIMINARY

REV. P1.0.8

MICROPROCESSOR INTERFACE

SIGNAL NAME

PIN #TYPE

DESCRIPTION

HW_HOST

Mode Control Input

This pin selects Hardware or Host mode. Leave this pin unconnected or tie

“High” to select Hardware mode.

For Host mode, this pin must be tied “Low”.

NOTE: Internally pulled “High” with a 50k

Ω resistor.

WR_R/W

TAOS_0

Write Input (Read/Write) - Host mode

Intel bus timing: A “Low” pulse on WR selects a write operation when CS

pin is “Low”.

Motorola bus timing: A “High” pulse on R/W selects a read operation and a

“Low” pulse on R/W selects a write operation when CS is “Low”.

Transmit All “Ones” Channel_0 - Hardware Mode

See “Transmit All Ones for Channel _0 - Hardware mode” on page 7.

NOTE: Internally pulled “Low” with a 50k

Ω resistor.

RD_DS

TAOS_1

Read Input (Data Strobe) - Host Mode

Intel bus timing: A “Low” pulse on RD selects a read operation when the CS

pin is “Low”.

Motorola bus timing: A “Low” pulse on DS indicates a read or write opera-

tion when the CS pin is “Low”.

Transmit All “Ones” Channel_1 - Hardware Mode

See “Transmit All Ones for Channel _0 - Hardware mode” on page 7.

NOTE: Internally pulled “Low” with a 50k

Ω resistor.

ALE_AS

TAOS_2

Address Latch Input (Address Strobe) - Host Mode

Intel bus timing: The address inputs are latched into the internal register on

the falling edge of ALE.

Motorola bus timing: The address inputs are latched into the internal regis-

ter on the falling edge of AS.

Transmit All “Ones” Channel_2 - Hardware Mode

See “Transmit All Ones for Channel _0 - Hardware mode” on page 7.

NOTE: Internally pulled “Low” with a 50k

Ω resistor.

TAOS_3

Chip Select Input - Host Mode

This signal must be “Low” in order to access the parallel port.

Transmit All “Ones” Channel_3 - Hardware Mode

See “Transmit All Ones for Channel _0 - Hardware mode” on page 7.

NOTE: Internally pulled “Low” with a 50k

Ω resistor.

RDY_DTACK

RXMUTE

Ready Output (Data Transfer Acknowledge Output) - Host Mode

Intel bus timing: RDY is asserted “High” to indicate the device has com-

pleted a read or write operation.

Motorola bus timing: DTACK is asserted "Low" to indicate the device has

completed a read or write cycle.

Receive Muting - Hardware mode

See “Receive Muting - Hardware mode” on page 5.

NOTE: Internally pulled “Low” with a 50k

Ω resistor.

XRT83SL34IV Datasheet(PDF) 11 Page - Exar Corporation

XRT83SL34IV Datasheet(HTML) 11 Page - Exar Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

Datasheet Download

Link URL